Hello, I have lost my lams for my Hammett 4 harness 4 treadles loom. I have decided to put on my other 2 harnness after weaving rugs with just two for the past 20 years and with my too many moves have lost my lams. I have the metal bracket thank goodness. I could make new lams but cannot find a decent picture of them on the webs. Does anyone have a good picture or at least the dimensions I need to make new ones and is there any reason why I can't just direct tie the harness to the harness's like I have my two now? Appreciate any and all answers. Thanks

Comments

Karen6

I believe I can help you - I have a Hammett counterbalance loom.  

My lams are 32 1/4 inches long, 3/4 inch wide, and 1 1/2 inch high.  I recommend that you measure the distance from the bracket to the farthest treadle on your loom to be sure that 32 1/4 inches is long enough to reach the farthest treadle.  And it should not be too long, either.  On my loom, the lam does not extend more than 1/2 inch beyond the last eye screw.

The bolt holes are about 3/4 inch in from the bracket ends of the lams, and centered horizontally.  Also, at that end each lam is rounded so there are no corners to keep the lams from rotating freely on the bolt.

Since you have the treadles and the shafts, you can easily match the locations on each lam for the eye screws you need to connect with the treadles and shafts.  

Let me know if you need photos.  Good luck!  

Karen

sequel (not verified)

I have a 32" and a 45" Hammett in the studio where I teach.  I can photo and measure either one if needed.

ewewoolen

Thank you so much for your reply. Looks like I will be making some lams. I had it in my mind that I could just direct tie to the treadles for a plain weave. Looks like I was wrong. Again, thank you for your help.

ewewoolen

Thanks so much for your reply. Karen 6 sent me very good measurements for making them. As I told her, I had it in my mind that I could just direct tie to the treadles for a plain weave and bypass the lams but another weaver friend said I can't, so that's that. I still don't know or haven't yet found why I can't just directly go to the treadles but I guess I would have found out once I started weaving! Do you know why? Again, thank you for your offer for photos. I may need them at some point.

sequel (not verified)

I don't see why you could not make a direct tie-up.  They were often sold that way.  Even when our looms have lamms, we will tie them 1 treadle per shaft, using the lamms.  There is not a great deal of mechanical advantage to lamms on the 32" looms.  If you do make a direct tie up, you may have to make a different tie up arrangement from the shafts to the treadles to keep everything even.  Make the lamms.  It's not hard!  Cut 4 sticks and drill some holes!

ewewoolen

Thanks so much again...since I am ready to warp I am going to try the direct tie up and I will make the lamms. What wood would you use? My loom is probably maple which I might be able to find but being in Colorado, pine is easier to acquire. I know maple would be much stronger but I would like to know what you would use. Thanks again Karen6.

Karen6

My old Hammett is probably made of pine or fir, and still works, so I think you would be fine using pine.  Weave away!

ewewoolen

Thanks again Karen. Appreciate your help.

ewewoolen

Thank you again to all who commented to my lost lams problem. I did go ahead and direct tied to my treadles and got a few projects done. However, it was a pain in the neck keeping my shafts straight so I am now making a set of lams. I love my old JL Hammet and sorry I lost it's lams. Thanks again.

ewewoolen

Here I am again with my lamms...Thank you Karen 6 and others who sent me the measurements for the lamms. I however negelected to ask how many eye screws will I need on the underside of each lamm. From what I can see, from the rare photos available, it looks 4 on each lamm. Is that correct? Since I am starting from scratch making these lamms it looks like it's going be an experience in lining up the screw eyes with the treadle screw eyes. Does anyone have a measurement between each screw eye per chance? Or maybe a photo? Thanks for any help.

Karen6

If you have four treadles and four lams, you need four eye screws on each treadle (=16) and four on the bottom side of each lam (=16).  

If you have six treadles and four lams, you need four eye screws on each treadle (=24) and six on the bottom side of each lam (=24).

Let your loom tell you the right distance apart the eye screws should be.  Lay the first lam across the treadles, with the left end even with the bracket, and parallel with the heddle frames.  It's a little tricky, because the treadle eye screws stick up.  Use a sharpie to mark the underside of the lam at each place where it crosses the treadle eye screws.  Repeat with the rest of the lams.  Center and pre-drill the holes and add the eye screws to the undersides of the lams.

You also need one eye screw on TOP of each lam (=4).  That eye screw needs to be lined up straight below the eye screw on the bottom of each shaft.

To reassemble the loom, (1) Mount the lams on the bracket; (2) Attach the cords or chains between the lams and the shafts, making sure the lams are level; and (3) Attach the cords between the lams and the treadles.

 

sandra.eberhar…

You don't have to use screw eyes.  You can drill 4 holes in each treadle and 4 holes in each lamm and thread cords through them.  You can use texsolve and begs or regular cord and knots.

Submitted by ewewoolen on