I hear and read the question over and over, which loom has the easiest tie-up.  It's a question I am now considering as I look around for a new loom.  I know when you go over 4 shafts you are considering more complex weave structures and, therefore, tie-ups will also be more complex.  Is there a loom out there with 8 shafts and "easy" tie-ups?

Perhaps we need to discuss what easy means.  I have a draft for shadow weave I am working on now with a tie- up that involves all eight treadles on my loom.  If I walk the treadles then I have to set it up and that takes some time.  Each treadle only has four shafts to it but they must be placed correctly.  Plus, my loom has a little funkiness that you have to start at the outer edges and move in or the pitch of the inner treadles will bring the lamms down on the outer treadles and cause them to go down when you don't want them.

So, in a new loom, I want to be able to get under my loom, be able to identify each cord for each shaft easily and not have to worry about the angle of the treadle I am tying up.  I own a Baby Wolf, 4s and I believe that is the easiest tie up I have ever seen.  I don't know what else is out there.  Do most larger looms have string coming from each lamm and you have to adjust the treadle angle as you add shafts to the treadle?  Is it difficult to catch the texsolv/chains with the stick you are using to tie up the shafts? 

That's what I am looking for, a loom where I can grab the correct string and slip it onto the treadle and it's done.  So, is there a loom that does that?  Which one?  Do all CM looms have complex tie=ups by nature?  A very well know teacher I once took class from told me not to buy a Swedish loom because the tie-up, on average, takes over an hour if you are using an 8s draft with 8 treadles.  Is this true? 

Claudia

The tie up on my current 8s loom:

 

Comments

lkautio (not verified)

You can color code your strings, write the shaft number on the lamms, and/or push one shaft down and tie it to all the appropriate treadles (rather than working treadle by treadle).  Macombers use steel hooks instead of cord and are very fast to tie.  Most jack looms don't require you to adjust the cord length to make the back shafts lift higher for a clean shed (it's done in the mechanism).  Some smaller looms can be tipped over (face down) to make tying up much easier. Countermarche looms take more tying because you tie both the rising and sinking shafts.  There are some with the tie-up on the side rather than underneath, and some looms can be retrofitted to have this feature.  Texsolv ladder cord is usually faster to tie than straight cord, but loses some of the adjustability (you are limited to the hole positions).

The easiest loom to tie is one with controlled by a computer dobby (yes, they come for 8 shafts).  They have the advantage of not limiting you to 8-12 treadles (different sheds) on an 8 shaft loom - no climbing around, no mashed fingers, no extra time, and no limits on the number of sheds. 

Best thing is to try a lot of looms, or look them over carefully in a round-robin.  If you are in a guild, it is fun to have occasional potlucks at different members homes so you can look at their looms and see the differences.

Laurie Autio

lkautio (not verified)

If you have a jack loom there is a far simpler universal tie-up for 4 shafts:  Direct tie.  Tie each treadle to one shaft and depress 1, 2, or 3 treadles together to get whatever shed you need. [For 3 treadles at a time press one with one foot and two with the other - easy when you get used to it).

Because the number of combinations escalates as you increase shafts, there is no "universal" tie-up for 8 shafts.  That is, with 8-12 treadles there is no way to make all the sheds in a way that they can be treadled with 3-4 treadles or less.

Laurie Autio

 

kerstinfroberg

This is a picture of 12 treadles tied up to my old (Swedish!) CM: (pic from the back side)

It is a system I made with inspiration from Öxabäck: screw eyes in the treadles, rings (key rings, easiest to buy) at the bottom of the cords, arrow pegs at the top of the lamms. All adjustment is then done *on top of* the lamms.

This is how I do it: take the cords through the appropriate hole(s) in the appropriate lamm(s). Check that the long cords are on the correct side of the lower lanmm(s). (Correct = same - either in front of, or in back of, but SAME. I usually have them in front of  their corresponding lower lamm) Take the pin, working methodically, one treadle at the time, catch the correct ring, put on pin, after (say) 4 rings go through next screw eye, find next rings etc.

After all pins are in place, roughly adjust the cord lengths, get out of the loom, check the sheds. Adjust cords as appropriate. And yes, I guess making a tie-up for 16 s/20 treadles (is what I have...) might take some 40-45 minutes, but I seldom use all shafts and all treadles...

As for an "universal tie-up" - I have never understood the idea. Must be much harder to operate, in comparison to a tie-up made to fit both the pattern and the treadling order. (Of course - I have never tried it, either...)

 

claudia (not verified)

Hi Kerstin,

That's what I am now considering doing, put the pins through the cords for the shafts needed for chosen pattern and then adjust at the lamms above the pins.  I like the idea of the key rings, much easier to catch and hold then the little slit in the texsolv. 

Thanks for all this info, much to consider.  I know that any 8s loom will take time to get the tie up correct.  I am happy to invest the time as long as I can get the needed result.

Claudia

kerstinfroberg

Oh - and I should say: one advantage with "ordinary" (=big) Swe looms is they are easy to climb into, lots of space to sit...

  :-D

BonnieI (not verified)

Claudia, shadow weave drafts can be written in two different ways. Both are found in some books and magazine articles. If you thread and treadle "on opposites" (parallel threading) then the tie-up is very simple and is treadled in walking order.  Using a parallel threading also makes it easy to create new drafts in shadow weave.  Or you can take one found in a magazine article and rearrange the threads and treadles. FiberworksPCW has an excellent tool for rearranging things on a draft. The drawdown (and the cloth) stay the same.

Bonnie

claudia (not verified)

Thanks Bonnie.  I am looking forward to the Fiberworks PCW due out this summer for Mac.  I got the TOTT loom set up and wove a sample today.  I'll post a picture soon, the shadow weave looks as though the web has ridges, it came out better than I hoped.

I'm continuing my loom research and now am interested in the Louet Spring.  I have found a couple people on Weavolution with this loom and will write to see what they do and don't like about the loom and the system of tie-ups.  The ad claims the tie up is easy but I'm not sure what they mean by a "parallel countermarche system". 

Claudia

debmcclintock

 someone somewhere in weavo was talking about the parallel countermarche system and posted a diagram here, maybe use the search function to find it?

Submitted by Anonymous (not verified) on