After two months of work, the 12-shaft Lervad from Wisconson is working!  This poor old loom had problems - the upper back beam was only 1/4" from the lower beam, not enough room for a tie-on bar.  The treadle bar was not holding the treadles in line with the holes in the lamms.  The heddle bars are quite heavy, and made of heavy hardwood, and were not balanced with the lamms and treadles.  The supplied heddles were 9", much too small for the heddle bars and depth of the 12 heddle bars.  I changed the heddles to 12 7/8" texsolv, moved the upper beam, added steel bars to the lower lams and treadles, repositioned the treadle bar and tied it up.  With all this, I still had gnashing lamms.  There wasn't enough distance between the heddles and the floor for everything to move.  I tied the upper lamms to the heddle bars, making them float. I also moved the beater up (thread spools turned out to be just the height needed, I'll replace then with pieces of wood) Now, no gnashing lamms, all the sheds are clear, heddles aren't falling.  After I got my heddles, I read serveral posts about heddle size and realized it probably would have worked without floating the lamms if I had used shorter heddles.  I used the green tie heddles on another loom, so that was what I ordered for this.  I also added a 20+ type pegboard.  Mine doesn't have the very nice finish work that Woolhouse tool's does, but it was a lot cheaper.  I also used braided polyester cord instead of texsolv for all of the cordage except wherer the cords go through the board,  Cheaper, easier to thread, and more resistant to chafe.  Lukke the Lervad is now making two scarves at once.  The rythm is different doing this, but it's kind of neat watching two color combinations develop at once.

                                .

Comments

Joanne Hall

You have really gone through a lot to get this loom working.  We need to give you an award.  I wonder if some other owner had made some changes to it that were not the best choices. Having the back beam so close to the warp beam doesn't sound right.  This company made a lot of looms for a long time.  I have a friend who had one and really liked it.

If you want to use the longer heddles, another thing you can do is to put the loom up on blocks.  Then you can lower the treadles which will give more space for the lamms to move.   Or you could get some Stadig loom feet.  They raise the loom up about an inch.

Joanne

Joanne Hall

It looks like you have a double warp beam.  That is why they are so close.  Perhaps they didn't consider that you might want to weave the last yard.

Is there a way to view the photos a little larger?

Joanne

sandra.eberhar…

I will try to put larger photos.  I thought I was putting large enough photos, but they didn't turn out the way I thought.  The loom came with the two back beams very close together, and the treadle bar out of place.  The loom frame has a lot of holes in it that don't do anything.  I think that Lervad made this in several versions, with one or two warp beams, and with 8 or 12 harnesses.  It looks like this loom started the assembly process as an 8 harness, single beam loom, and got extra treadles, heddles and lamms before it left the factory. The upper beam was originally Also, at some time I beleive that it was moved and all of the hardware, including heddles, were lost.  There are marks for larger washers on the uprights.  I wanted a multiple shaft loom compact enough to put upstairs in my house and I am very happy with this.   I think it was well worth the effort, and I really feel for all the people who have tried to use it and been less than successful.   

sandra.eberhar…

i think that all of problems that I have found with this loom (except the very small heddles) came with it from the factory.  The bolts that hold the loom together are iron, not steel.  If this were an American loom, that might put the date of manufacture about 1900-1920.  I have a rug loom made about this time with similar hardware and it is very worn.  You can see that someone used it a lot.  This loom has very little wear and tear.  The previous owner only tied up four harnesses (tying up more than that and you run into problems with the treadle misallignment.  

Joanne Hall

putting the beater back down, without the spools of thread, now that you have everything in order?  It looks like the warp threads will hit the bottom of the reed and that would stop the opening of the shed.  On a countermarch or counterbalance loom the warp threads usually do not touch the bottom of the reed. 

Joanne

ReedGuy

As Joanne said it looks like you beater is a notch too high. Your warp is going to chafe on the race of the beater and wear at your warp. It will also restrict your swing. Have you separated the top of the beater for a warping trapeze? I see there are no notches on the castle for the beater to be adjusted for the depth of your weaving (between the breast beam and shafts) as you weave between warp advances. That would be beneficial to add them.

You can weave about 8 inches (maybe wider, I have a wide shuttle race on mine for fly shuttle) instead of maybe 4". Not crittical but nice. Also with the pivots attached to the back, the beater will roll back toward the shafts when at rest instead of having to bush it. Closer to the shafts means wider shed, useful aid when your starting with the beater closest to you and you have a heavy beater.

I'm not sure about your troubles with the treadles. Usually they just sway as do the lamms. It might be that your tie up is not consistent by the way the cords go up from the treadles to the top lamms. Make sure they all either go by the back or the front of the same numbered lower lamm bar on the way up to the upper lamm. If not, this will restrict their movement.

Sara von Tresckow

JUst FYI - as someone who learned to weave just south of the Danish border in the late 1970's - your loom looks to be from 1975 - 1985 in vintage.

This model was quite popular and should be put together pretty much the same as any other CM loom. Much of what I read of your issues were not factory caused - someone on this side of the pond didn't understand the loom from the getgo.

sandra.eberhar…

No, the problems with the back beams and the treadles were done at the factory.  The joinery, glued dowel joints was original.  It is quite easy to see if the original dowels have been removed and repositioned, and these were not.  The treadle bar was positioned at the factory to work with eight harnesses, but the 12 lamms are drilled to line up with a treadle bar that was much longer.  The 12 treadles fit on the original bar (with NO spaces) but did not line up with the holes in the lamms.  To make them line up, and space them to be usable, (unless you weave with ice skates on) the treadle bar had to be 10" longer.  It is possible that the loom was originally 8 harnesses and someone added four, but this would have been odd becuase I don't think this loom ever worked with 12 harness before.  There was no way to tie it up, and since it doesn't balance at all, the shafts sink to an unworkable level.  Not everything that comes out of a factory, whether European, American, or Asian, is properly put together.  Thanks for the dating on this.  I know that American looms with iron hardware date from ~ 1900, but I'm not sure how long European manufacturers used iron.

sandra.eberhar…

I noted that there are marks on the pieces from much larger washers than came with the loom, and the nuts are steel: the hardware to the loom was lost at some time, probably with the heddles.  If someone had two of these, one 8 and one 12 harnesses, and mixed the parts when they were dismantling them, that would explain why this one is so out of line.  This loom has room for all 12 jacks and lamms easily; would the 8 harness version had this much room, or would the spaces allowed be much narrower?

Submitted by sandra.eberhar… on