Hi guys, I've settled in my new home and studio and am weaving away.  I have a new concrete floor, sealed, that my Harrisville loom sits on.  I've given it some time but I do need to do something to keep the loom from walking.  The loom posts are 2 3/4 inch square so I am guessing I need to look for something with at least a 3 " square opening to set the loom post in.  Has anyone found anything online that they like and love on concrete floors.

I've checked on the glimarka post pads and they are not wide enough.

I've tried searching on several word variations and haven't found any prior conversations in these forums.  They might exist but I can't find them.

Any suggestions for a concrete floor/loom interaction would be most welcome!  We live where I usually have to mail order to avoid miles of driving so I am not opposed to ordering on line.......

I am going to try my auto supply store and hardware store and enter the weaver's trance of inspecting gizmos/equipment for alternative weaver's use in our fiber universe.

Thanks for any suggestions!  Deb Mc (who is going back to the studio to shove her loom around some more!)

Comments

WallyWeaver (not verified)

Have you considered a rug under your loom?  A friend suggested that when I was starting weaving, and I thought she was nuts.  I have since found it's not a bad idea.  Helps keep loom from moving around, provides some sound/ noise-deadening quality, and isn't all that difficult to vacuum periodically.

Or look for rubber "caster cups" at your favorite home improvement store.  We use 'em under the legs of chairs, loveseat, etc. in our living room to protect the hardwood floors.  I think Home Depot, Lowe's, etc. or your local hardware store should likely have them in various sizes, including 3" squares.

Good luck!

feltedbag (not verified)

Have you thought about that non-skid kitchen shelf lining?  I use it under my KitchenAide mixer so that it doesn't walk off the kitchen counter when I use the dough hook.  The mixer stays right where it is suppose to me.  You could cut squares the size you need.

Annette (not verified)

Have you tried the material you buy to keep rugs from sliding.  I find it works great.  You can buy it at the hardware store or order it  online.  It is a kind of puffy or squishy material in a checkerboard pattern.  I use a small one and cut pieces to size for my loom legs.  Note, don't get carried away, like I did, and put them on your bench feet.  You go to get up and push back from the loom, but your bench doesn't...  Ouch!  The stuff really keeps things put!

Hope this helps.

debmcclintock

I have some of the non-skid ribbed shelf lining left over that I thought for sure would work....I've tried it on both sides, ribbed and non ribbed up and down, still slides.  I think I need something thicker.

Someone on another list suggested some plush rug squares.  I'm adding that to my list of items to look for! 

debmcclintock

Thanks, I'll add that to my look around list when I drive into town....love the bench push reality check! 

Bonnie Datta (not verified)

Hi.  I found that heavy weights help -- like the 50 lb ones used for muscle building -- put one on each side.  That, combined with some of the non-skid shelving should help.  I also stand on the "foot beam" when I beat.  But personally, I found that the only way to keep my 60" Glimakra from moving when I am weaving rugs and tapestries with a heavy beat, is to put planks between the front of the frame and the wall.  Putting thick (handwoven) rugs up close to the planks reduces the chances of tripping over them.

Bonnie.

 

Sherri (not verified)

I use those rubber door stoppers on the two front legs--by the beater. Use a crowbar to lift the loom (I have a heavy Cranbrook) just a bit and slip the pointy end under the leg just a smidge. No more moving loom! Plus, they're cheap and can be found in many places.

debmcclintock

 ohh, I like the idea of rubber door stoppers, thanks!

Bonnie, I was thinking about doing the plank/wall thing but we just built the house and I don't want to crack the stucco right away!  I was trying the stand on the "foot beam" thing but this particular loom's "foot beam" isn't directly on the floor like my old Cranbrook was so it bends a bit, that's a bit unnerving when one stands on it!

thank you to all for the suggestions!  I'll report back with what works for me and my concrete floor!

Submitted by debmcclintock on