I bought this loom at my local guild's auction for $12!!  I am a newbie weaver and have only attempted to weave once on a rigid heddle loom.  I'm really wanting to get this working but as you can see I'm missing the heddles.  I also have no idea what kind of loom this is or what the pieces I'm looking for or needing to make look like.  Any information about this loom would be great!!

Thank you!!

Natalie

Comments

claudia (not verified)

It looks as though you are missing the harness to hold the heddles.  Are there any distinguishing marks anywhere on the loom? numbers?  Can you take a couple more pictures so we can see the center where the heddles belong?

This is a fun little mystery but I have a feeling there is someone who knows more about this than me. 

Claudia

laurafry

I suspect it's a double rigid heddle loom.  Maybe you can find current rigid heddles to fit.....

Cheers,

Laura

barknknit (not verified)

I don't think it's a rigid heddle because of the beater with the reed.  I've looked everywhere and it looks most like a shaft loom.  I'll take more pictures of the inside. :)  

Hope I can get it working! :)


Thank you!

Bonnie Datta (not verified)

Does it have a tensioning system -- a ratchet and pawl mechanism for tightening the warp?  I think I see one on the front, not so sure about the back.  Also, I think I can see that there is a cloth beam and a warp beam, right?  If so, then I'd start by getting some texsolve or hand-made string heddles, and hang them on some metal rods that are thin enough to raise up through the keyhole and rest on the little shoulders of the keyhole.  You'll need a second bar on the bottom to weight the bottoms of the heddles, and the heddle eyes should be just an inch or so below the line from the front beam to the back beam when lowered, and just and inch or so above that line when raised.   If that can be set up then you'd be able to have 4 shafts, and you'd need both hands to raise and lower them by grasping the rods and re-positioning them in the keyhole.  Might work.

Bonnie.

 

laurafry

I think Bonnie has hit the nail on the head - probably two heddle bars fit in those little slots on each side.  

Cheers,

Laura

barknknit (not verified)

Bonnie...that makes a lot of sense!!!  I think I might order some metal heddles though instead of the string ones.  

Thank you SO much for your comments...I think I finally understand what I need to do!

Also..it does have a ratchet on both sides.

barknknit (not verified)

Oh another question....how many heddles do you think I'd need to order for 4 shafts?

Would these work?  9.5 inch ones?

http://halcyonyarn.com/products/equipment/6895000f.html

or would these be better or worse?

http://halcyonyarn.com/products/equipment/6210500w.html

both come in 100 packs.

Bonnie Datta (not verified)

Glad I could help.  I think wire heddles will be better because they will maintain the spacing without having to weight the bottom heddle rods.  You will have to be able to round out the top loops to fit a round rod, because I think a round rod will work better resting on the little shoulders of the key hole.  (I have some 9.5 inch heddles that I don't need, that I'll sell for $3.00 per hundred plus postage.)  If you'll be weaving at 10 epi, 24" wide you'll need 240 heddles, so figure up or down from that.

Bonnie.

 

CraftinSusan

For your purposes either heddle style should work.  The second one states that is has a larger hole for thicker yarns if that is a consideration.

I don't know how wide your loom is.  On my 15 3/4 inch  table loom, each shaft has 50 heddles.

FYI:  There were a couple of Rigid Heddle looms made with beaters so it is possible that your loom is one of those.  But at this point you could go either way.

barknknit (not verified)

The only Reed I have with it is a 12 dents per inch?  Right?  And I think my loom is around 23.5 inches wide.  And then I hve to take into account how many heddles I want right?? 

Let me measure my loom to see if 9.5 work.  How many do you have Bonnie?

loomroomcat (not verified)

there is gal on  www. kbbspin.org   on the loom section, page 2 with texsolve heddle 9 3/8" for sale.  I think she has 600 and the price is very good.  maybe those would work for you.

barknknit (not verified)

Bonnie, I'm new to this weavolution and I can't figure out how to message you directly.  Would you email me at [email protected].  I think I'd like to order the lot of them.  You said they are 9.5 and wire heddles?  It would be a good start.  My hubby already told me he could make me the bars.

claudia (not verified)

To use the Message feature, click on the word "Messages" in the list on the left side of the page. That list will help you navigate around the site. Hope that helps. Feel free to contact me with any questions [email protected] Claudia, Weavolution co-founder
Submitted by Anonymous (not verified) on