I’m a textile design graduate from Ireland keen to start up my own craft/design business and took the opportunity to buy a second-hand Glimakra vertical countermarch loom a couple of years ago.  After keeping it in storage for a while due to lack of space to set it up, earlier this year I began to put all the pieces together in my newly-built shed, like a giant jigsaw puzzle.  Unfortunately I discovered that the loom had some woodworm and so I spent some time treating the pieces and varnishing to protect from the damp Irish winter in an unheated shed.  Although the pieces did get a little damp, none of them appear to be warped badly and everything fitted together as it should.  Now summer has come it’s all nicely dried out.  Last week I finished threading up my first practise warp for a simple ‘goose-eye’ practise weave with 4 shafts (project from the Big Book of Weaving actually). 

 This week I apprehensively attempted the tie-up of the shafts, lamms and treadles.  Because I had a feeling it would be challenging, I had done lots of research with the help of this site, Glimakra USA info pages and The Big Book of Weaving.  When I remove the locking pin of the countermarch, unfortunately all the shafts fall down, until they rest on the sides of the loom frame and warp.  The jacks fall into a horizontal position and the lower (long) lamms fall down to the bottom side bar of the loom. 

 I have read Joanne Hall’s info sheets on Glimakra USA and previous posts on this forum, but just cannot figure out what is going wrong.  I’ve tried raising the upper lamms so that they slant upwards slightly, and tying up two extra treadles to add weight to the lower lamms but this doesn’t do anything at all as the lamms have already fallen as low as they can.  As far as I can see, I’ve followed the tie-up instructions to the letter, it’s exasperating!  Unfortunately I made the mistake of buying the loom unassembled (as the previous owner didn’t have the space for it,) and haven’t set up this type of loom before.  The shafts and upper lamms do seem a little heavier than Joanne Hall has recommended on these pages previously, and heavier than new extra ones I have purchased from a UK Glimakra supplier, but as far as I’m aware they are the original Glimakra ones supplied with the loom and have been used by the previous owner. Surely the original supplier would not have supplied the loom with pieces that weren’t appropriate and a nightmare to balance? 

 The loom dates from about 1995 I believe, and weaves 150cm widths.  The heddles are the standard recommended 11 inch length.  When I read about how good Glimakra looms are I felt lucky and excited to have got this loom locally, as they aren’t common over here, but I don’t think I’d have bought it if I’d realised the set-up would be this difficult.  I’ve already spent so much time and money on the loom, I can’t give up before I’ve even started weaving but at the moment it seems impossible!  I simply cannot see how everything could balance when the locking pin is removed.  Should the jacks really stay in a vertical position when the pin is removed?

I've attached an image showing the tie-up when viewed from the back of the loom, with the locking pin in place.  As you can see, the upper lamms are slanting up slightly.  I began with them parallel as advised in The Big Book of Weaving but re-adjusted them to this angle to see if it helped, but it hasn't made any difference.

If anybody has a similar loom or has seen this problem before, I'd really appreciate any help.  Thank-you

Comments

sarahnopp (not verified)

Have you looked at this white paper from Weavers magazine? http://www.weaversschool.com/docs/Countermarch.pdf It helped me a bit. Of course, having a mentor come over to point out what I was doing wrong helped more :) But pictures do help! I spent a lot of time looking at pictures of warped up countermarch looms, I am sure you have too.

anatcheva (not verified)

Are the jacks attached to the lower lamms? I don't see the attachment in the photo. Dress Your Loom the Swedish Ways, a video by Becky Ashenden, is a wonderful resource in tying up a countermarch. http://www.vavstuga.com/store/videos.shtml

Sara von Tresckow

This may sound odd, but do you have a warp on the loom? It is not apparent from the photo. If the loom is not dressed with a warp under tension, this exacerbates the dropping of shafts when the pins are removed.

Your setup looks decent from the photo. The slight upward tilt of the lams is not going to make a substantial difference over having them straight. The exaggerated slant in the article from Madelyn has sort of been overridden since it appeared - this was "extreme shedding" that is really not necessary.

You are seeking balance with your loom. If it is warped, try treadling a few picks and see how the shed behaves. I've seen it with a loom like this if there is a narrow warp, that the shafts drop or the treadles do not always return to exact "neutral" - BUT - and this is important, when depressing trhe treadles and weaving, the shed floor is tight and even and the fabric develops as you want it. You have a very large loom and there needs to be counterweight all around to have it function well - I'd say that warps under 18" would cause that balance to be "shorted". The treadle weight should somehow balance the forces in play. Perhaps weighting the treadles would help the situation more than playing with the cords that appear correctly set up when the locking pin is in place. The Oxaback looms come with heavy beech treadles and I don't see this happening.

As for the coupers on top - they shouldn't splay out all over the place, but they do tend to spread a bit when the pin is removed. Again - your main concern is a good shed with an even shed floor - and above all else - quality fabric. I learned to weave in Germany. They were sticklers about fabric quality and produced accordingly on looms that looked so roughly set up and maintained that half of this group would have a heart attack. Main thing was, they had a good shed and good tension.

Joanne Hall

As Sara suggests, start to weave and then make adjustments later.  If the bottom of the shed is not good, weave at least an inch before you make any adjustments.

And you can tie those two extra treadles up just for the weight the treadles add to hold up the shafts. 

I am curious about those extra knoted cords on your lower lamms.

Joanne 

Joanne Hall

Hi Sarah,

These instructions, which Madelyn wrote, assume that you are using 13 inch long heddles.  When the heddles are that long, one needs to compensate for it.  Plus, the looms in the 70s and early 80s had lower lamms which were not heavy enough and that complicated the tie-up even more.  So, these instructions were for that time.  Today the lower lamms balance better and the heddles are 11 inches long.  So, the tie-up is actually easier today.

Joanne

Nicola

Thanks everyone for all the suggestions. This website is such a great resource, all credit to the contributors and founders.  Unfortunately I won't be back at my loom for about 10 days as my workshop is at my parents house quite far from my day-job.  I'll definitely be examining the set-up more closely when I get back.

Sorry I didn't realise the photo I posted was cropped so detail was cut out.  I've attached another image (hopefully not cropped,) which shows what happens when the locking pins are removed, as you can see the lower lamms are connected but have collapsed right down to the bottom of the loom frame and the shafts are resting on the sidebars. For this reason, tying up the extra treadles to weight the lower lamms doesn't make any difference (I tried two,) as it just pulls them down further.  In the current state it's also impossible to treadle, and so, even begin to weave, as the treadles have fallen down low and won't move.   I originally tied them up at about 8" off the floor.  I think I'm definitely missing a trick somehow.  The warp is already on the loom, its 80cm wide.  However I didn't think about the tension affecting the balance so I will try increasing the tension, thanks for the suggestion, Sara.

Thanks for the dvd contact, anatcheva, I'm going to see if I can find a UK supplier.  Also, Joanne, perhaps you could tell me if I can purchase your book in a downloadable form at all?  The knots, by the way, are just the extra cord length knotted for neatness at the top of the lower lamms.  I've kept the cords long enough to reach the upper lamms so that I don't have to change them if I change the tie-up, a suggestion I took from Madelyn Van Der Hoogt's article.  I had seen her article but haven't followed it exactly as my heddles are the standard 11".

I'll let you know if I have any luck when I get back to the workshop... 

Joanne Hall

of the tie-up at the top of the loom, when you get back.  There is something wrong with the tie-up.  I can send a diagram.  Write to me at:

[email protected]

sarahnopp (not verified)

Ahh I see what you mean Joanne. I was using all sorts of information when I was trying to figure out and balance my little Bergman countermarch. So I usually discregarded information that was specific to a partcular loom, such as dimensions, etc. I tend to be a "directions are really only suggestions" personality type anyway :)

ReedGuy

Acts to me the tie-up to the jacks and shafts is not correct, as Joanne suggests. The shafts tie up to the holes in the jacks that are furtherest apart, the lower lamms to the hole at the end that is the shortest distance from the middle hole. Too much fulcrum on the shafts the way it's now tied. When the jacks are not tied up, they actually hang upside down on the rack.

Nicola

Hi all, thanks your suggestions and patience. 

I got back at my loom today, and happy to say that I am finally weaving!  After the last few posts referring to the tie-up at the top of the loom, I studied Joanne's helpful articles on her Glimakra USA website and realised that I had simply put the shaft cords the wrong way round - on the left (same side as the ends of the long lamms,) I had them tied up to the second hole from the top on the jacks rather than the hole at the bottom. 

I think I made this mistake because I was looking at an image in the Big Book of Weaving which shows the shaft tie-up without the lamm tie-up from the back rather than the front, or on a loom where the lamms pivot from the left rather than the right.  I was obviously so distracted by the complicated tie-up at the bottom of my loom that I managed to completely overlook the obvious mistake at the top. I didn't even need to make any shed adjustments, it seems to be weaving beautifully.  I feel pretty silly now that I actually considered that the problem could be the loom itself rather than my inexperience - but also very glad!  I've attached a pic of how the tie-up was before I swapped the cords around, just so that any other new weavers can see how not to do it...

Thanks for offering to email me a diagram Joanne - I actually already had your guidelines printed off but simply overlooked my error.  I'm also very glad I followed Sara's advice from an older post and set the loom up for the first time with a 4-shaft weave rather than the complex 8-shaft pattern I had intended!  I'm looking forward to progressing my skills now and designing some interesting fabrics.

Nicola

Submitted by Nicola on