I f you don't have a warping board you can clamp some stakes to a table and use those as warping pegs. They will need to be very firmly clamped so don't clamp them to a good table. In this photo they are clamped HARD to a board.

Some people drive stakes into the ground in their garden or use the pegs on their inkle looms. What ever way you choose, make sure your stakes are FIRMLY grounded. THEY MUST NOT BE ABLE TO MOVE AT ALL !!. As you wind your warp, loose stakes will start to lean in towards each other and this will create uneven tension across your warp.

                                                      

1. Tie your warp to the first stake with a big loop so that it easy to slip off when you finish and slip on to your loom bar.

2. Wind the yarn in a figure-of-eight creating a cross in the middle.

3. Cut and tie on yarn at the starting stake. Finish at stake A again tying around the stake with a big loop.

 

I have photos and video on basic warping on my Flikr page here.............

www.flickr.com/photos/39560980@N05/sets/72157620403266756/

 

Laverne

 

Comments

mischiefmanaged (not verified)

Thanks for this. I have a warping board but did not know how to start or end for a continuous warp until I looked at the diagrams. I have wound a smooth cotton warp for my 2nd try at backstrap weaving, so I am keen to get to it!

Do others use a warping board? I have a bit of trouble spreading my warp out on the bars after it is jammed together on the warping board.

bolivian warmi

Hi Cindy,

I am glad the diagrams helped-lots mor stuff on my Flikr page if you need-videos too.

To help spread your warps once off the board..............

you can encircle groups of warps by twining a cord around them as you go winding the warp. If I am winding a wide warp, I do this for every group of ten or twenty warps-also helps if you lose track counting. This will keep everything nicely spread out when you put the warp on your loom bars.

hope this helps.

when you say that you are starting your second warp, does that mean the first one was a success? Can we see? Please!

Just start a new thread to show us your work. Photo uploading instructions are here..........

www.weavolution.com/node/1328

Laverne

mischiefmanaged (not verified)

Thanks for the link to the photo instructions; I'll use them when I've gotten a bit done. My first warp was the sticky one and I only wove about 2 inches before deciding I needed a friendlier warp ;) I hope to have something to photograph later this week. Cindy

Aunt Janet (not verified)

Hi Cindy,

   i had to chuckle about your 2 inch weaving.  The same thing just happened to me with my handspun alpaca yarn.  Boy was that one sticky!  I had warped for double weave.  The yarn was quite fine, like a 8/10 cotton, and three lovely alpaca colors.  Alas, this was just too difficult to change sheds.  Two inches of weaving and I'm trying to think of what I can do with the rest of it.  Maybe I can make Kumihimo cord with the two inches of double weave, including a nice arrow in the pick-up area, as a kind of necklace, or a handle on something.  I left a long fringe.  It might work.

   Anyway, I'm also on to a more friendly warp.

Aunt Janet

Caroline (not verified)

I used hair conditioner diluted with water as a spray on my horrid sticky warp - it works once its dried and does make things easier to handle.

mischiefmanaged (not verified)

Here's how not to warp for backstrap weaving (and this all happened over the course of about a week):

1. Choose a favorite yarn that's fuzzy and won't make sheds (see above). Decide to use this warp as weft for some future project  and remove it from loom parts.

2. Choose a smooth non-fuzzy yarn for next warp. Become enthralled with the Doctor Who episode you are watching while warping and forget to use a counting string. Also be not too careful with beginning and ending of warp so that first and last warp pairs have a tension all their own. Decide someday you will know how to fix tension of edge warps and set warp aside. Decide it doesn't count since you actually didn't weave on it.

3. This time pay attention while warping and wind a nice long one so that you can practice and maybe make a simple belt too. Discover while trying to put this on loom that the nice long warp is too long for the room where I am weaving and I'd have to sit outside . . . if I was willing to run the warp through the basement window into the yard. I'm not. Decide this one doesn't count either.

4. Review Weavezine video on string heddles; reread warping section of Techniques of Guatemalan Weaving.  Notice that auther winds warp with 2 crosses. Although not sure why it would make a difference, decide it can't hurt and plan to try it. Consider sleeping with book under pillow in case knowledge can be transferred by osmosis. Feel glad that I am not superstitious.

5. Put on CD of Andean folk music. Wear Bolivian sweater. Wonder if coffee happens to be from Guatemala or other backstrap weaving land. Wind 1 yard warp, tensioning carefully, with two crosses. Notice end warps still funky  (see first photo) but pretend they are not.

6. Search for bungee cords to secure loom at lower level. Decide that 12 years of marriage is not enough to fathom how husband thinks and figure out where he put bungee cords last, so tie loom on with other stuff.

7. Make much improved string heddles and try weaving. Ah, sweet success (second photo).

bolivian warmi

Hi Cindy!

Thanks for the giggles!!

A couple of tips............

### Too long warp....you can roll up the far end of your warp and then go unrolling it as needed. I have photos of this on my Flikr page...........

www.flickr.com/photos/39560980@N05/sets/72157621714345915/

Others members have suggested chaining-never tried this myself. You could wind a circular warp but I wouldn't get into that now.

### Edge warps funky..........just untie the knots, adjust and re-tie tighter-happens to me too all the time.

### Two crosses.......this is handy but I always warp with one cross. I use a second cross only when my shed stick is rolling about and being a nuisance. I only decide if it is necessary once I am in my loom and weaving. My teachers here in Bolivia and Peru don't use a second cross whereas almost everyone I saw  in Guatemala did. It is simple to set up a second cross once you are already set up in your loom. This is the way I was taught in Guatemala. You will need an additonal stick-let's call it  ''stick A''.

Step 1......set up your string heddles and insert your shed stick.

                                     

Step 2......open the shed stick shed and                                 Step 3......remove the shed stick.

place your sword within at the weaving line.                                                                                      

                                       

Step 4......open the heddle shed and                                         Step 5....Open the shed stick shed using the sword

place a stick (stick A) in the shed.                                               and place your shed stick within beyond the heddles

                                                                                                           and next to stick A.

 

Step 6....tape or tie these two sticks together.  

Wish I could see a bigger picture of your sucessful warp. Are you doing warp faced? I can't tell how close together your warps are. The string heddles look great!

Good on you for your perseverence and for sharing all the oopsies with us. I once made my string heddles in the same color yarn as my warp and instead of cutting the tail of the heddle string when I finished, I cut the warp! Arrgh!

Enjoy your sweet sucess.

Laverne

 

 

 

 

DianneStucki (not verified)

Boy, all those "not to's" sure do sound familiar! 

 

I have learned that Doctor Who must wait till AFTER warping is done. It's just too distracting otherwise. :-)

bolivian warmi

I have had some questions about knots. I was never a girl guide or a brownie so was thrilled to learn this one as an adult from my Navajo Weaving teacher. I use this when warping to tie the final warp to the stake. It helps you to tie the warp leaving a large loop while maintaining tension on that final warp.

 

   

1.Make a loop as shown and pass the tail around the warping stake. This is the ''main'' loop.

                                     

2. Grip the base of the loop with your left hand                     3. Pass the tail under the main warp thread and through the 

and pass the tail through.                                                          main loop. I am forming a secondary loop around my middle                                                                                                          finger.

                      

4. Continue gripping the base of the main loop                      5.The main loop will disappear under your thumb.

while pulling on the warp with your other hand.                       The midde finger continues to hold the 2ndary loop. 

This will close the main loop.

                      

6. Pull on the secondary loop. This will take up                      7. Pull the tail to close the secondary loop.

all the slack in the warp. Pull it really tight while

maintaining the grip with your left hand.

Here it is finished.

The first moves can be performed with the final warp slack. The last moves will take up all the slack in the warp and finish off the knot. If you get it really tight, you won't need to untie and retie once you have your warp on the loom.

I love knots-anyone else got any good ones?

Laverne

                                                                                                                                    

rose Goldielocks (not verified)

Thanks!.... my slip knots did not work well. (they tightened on the beam and got stuck)... and the overhand knots just pulled loose!

 

bolivian warmi

I have a video on my blog his week showing winding a warp, the bowline knot in action, getting the warp off the stakes and onto the loom bars, setting up the loom, making heddles-the whole lot in one package!!!

backstrapweaving.wordpress.com/

There is also a bit on second crosses and a sneak peek at some edgings and braids which may show up in future tutorials. Take a look!  :-)

Laverne

Submitted by bolivian warmi on