People give me looms to rennovate.  I do that and give them away, for the cost of any materials that I have to buy, to a junior or senior weaving student at Mass Art.   The head of the weaving department usually picks the student.  Anyway, I picked up a 4 shaft F L Ahrens loom today.   It's a small jack loom with 4 direct tie-up treddles.  It has string heddles and really beautiful wood.   I'm wondering if anyone out there has one that they could take a few pictures of for me?

Above where each shaft would hang are 4 wooden pulleys,one on each side and two in the middle.  Under each shaft are two small jacks, one on each side.   The jacks on each side are tied togethe with a long spring.  The shafts aren't hanging just now and it's partly disambled.    I've googled the name, but didn't find much.   I'm sure I can figure it out in the end, but a few pictures would save me some time.

Thanks,

Comments

SallyE (not verified)

I finally looked closely at the name plate and see that it is a F J Ahrens loom - one of the founders of AVL I think.   I found some pictures and a copy of a patent that he got in 1946.   That patent, and the pictures I've found, show a loom that is able to tie up on the side rather than under the loom.  

But the loom I have doesn't have that side tie-up.   I think it probably pre-dates that patent.   I guess I'll just have to fuss with it a bit.   The wood is beautiful - some birds eye maple and some tiger maple.   It's going to clean up nicely!   I'll post pictures once I get some of the dirt off of it.

 

Bonnie Inouye (not verified)

Jim lived in California for many years and then moved to Utah where he continued to weave and improve looms and weaving equipment in his woodworking shop well into his 90s. Yes, he's the A in AVL. Many of his Ahrens looms and the earlier AVL looms have beautiful wood. He made several different kinds of looms and paid attention to how people can make efficient use of their time and bodies. That side tie-up system is especially useful for looms with 8 or 12 shafts and you can find it on the AVL Home Loom  as well as many older Ahrens looms.

Jim was a keynote speaker for the Complex Weavers seminars in 1990. I met him there, later visiting his home and studio in Salt Lake City with a mutual friend, Judy Eatough. An amazing man! I was so lucky to have that opportunity, thanks to Judy.

Bonnie

JillLeeJones

I have a 10 shaft FJ Ahrens loom and am wondering how to wind the warp. It does not have a crank on the rear beam and looks as if it never had one. The only way the warp can be loaded is by hand turning the rear beam which is a pain. Is there something I'm missing here? 

SallyE (not verified)

No, you are missing nothing.   The only way is to hand wind the warp beam.   There is no back beam or breast beam - only a warp beam and a cloth beam.  These are "minimalist" looms!  Look at the bright side - there is no handle to misplace!

If you were willing to do in, you could a 1/4" drill a hole clear through the beam near one end and insert a piece of 1/4" steel rod and use that to help you turn the beam. 

 

 

JillLeeJones

SallyE, thank you. I just saw your response here. I am in the process of weaving my first project on this loom. I beamed the warp by hand, and after doing it, I have to say that I prefer this method! I was able to watch my warp as it laid down and deal with any snags or problems ahead of time (linen!). I really don't want to do anything to alter the loom. I am really enjoying this loom, it weaves like a dream. So many thoughtful innovations on it. Hard to believe that it was built in the 40s! Thanks again. 

[email protected]

Picked up my new to me loom in California this past weekend.  It is an 18 shaft loom and in such wonderful shape!  I have to put it back together which has me a bit nervous...but excited to have this jewel!

Submitted by Anonymous (not verified) on