Hello all,

I am a new weaver, working on a little old English Dryad counterbalance floor loom. I've read a few tips online and in one of my books about adjustments for getting good sheds when treadling tie-ups that are "asymmetrical" 1 against 3, etc. I've played around with the length of the texsolv cords between the lamms and the harnesses, and a bit with the length of those above the harnesses. Some improvement seemed to be happening, but I still need to really stomp on the treadles to open a fairly clear shed, except on the symmetrical tie-ups. 

There's lots of advice about this kind of thing online, but everyone seems to have either rollers above the harnesses, or one large pulley and horses. Some recommendations have been to raise the top pulley/roller, but that is not an option for me, although I could shorten the cords from the top pulley to the smaller pulleys. I haven't tried this. As you can see in the first photo below, the Dryad has one upper pulley, and two smaller pulleys, on each side. The second photo shows a problem shed. 

Also, I am having irregular sheds that seem to be related to the harnesses pulling unevenly, and sometimes remaining that way even at rest. I've shown this in the third photo, and the fourth shows the wonkiness remaining, even with the treadle released. You can see a bunch of unused heddles down at one end of the last two harnesses, but they aren't connected to anything but the tops of each harness, and aren't responsible for drawing it down on that end.

So, my questions are:

1. Are any of these problems worse BECAUSE the Dryad has pulleys rather than rollers or horses? If so, I could think about modifying it.

2. What would you advise I try, and it what order? Originally I was most bothered by the poor sheds, but probably the uneven bit is more of a problem?

Thanks to all you experienced counter-balancers; I have already learned so much from your discussions!

Jennifer (Textilis)

 

 

 

 

Comments

Dawn McCarthy

First I would remove some of the lease sticks (you only need 2 - one for each segment of cross) and also move them farther back toward the back beam.  This will give more space for shedding action.  I had a loom with top pulleys and lower pulleys vs a pole and pulleys and I personally found it a little tricky to balance (I ended up using elastics to stabilize the shafts).  Check that when at rest all threads are in the same position in the heddle eye, you may need to adjust the height of the shafts.

Don't try to create a huge shed, just one that is enough for the shuttle and has a clean floor.  Visit Joanne Hall's site at Glimakra where she gives good advice on CB loom set up.

Dawn

Kade1301

 - that was one piece of advice from Joanne Hall. Which makes the loom look more orderly. I'm not sure whether it really helps with the shed - but I like my loom a lot a lot better with the bungee cords. You need two cords per shaft, long enough to go from around the shaft at rest to the upper beam - I bought mine by the meter in a DIY store (in a pinch elastic band used for clothing will do - if you use bungee cord, buy the thinnest, otherwise you'll have to use more force to treadle. Also it's cheaper.). That's the second thing to do, after adjusting the lease sticks as Dawn said (or even taking them out altogether - I have read somewhere that how well unbalanced sheds work on counterbalance looms depends on the size of the loom, i. e. the distance between back beam and shafts).

If you are still not happy after those two improvements, I'd play around with the treadle tie-ups (basic rule, if the string is shorter, the shaft gets pulled down further - higher treadles make for larger sheds. Within limits, obviously.).

Last but not least, another thing to bear in mind is that the top of the shed isn't all that important (unless warp ends are so far down that the shuttle goes over them) - really important is having a smooth bottom for the shuttle to glide over. That shafts stay in position, all wonky and irregular after releasing a treadle is normal, according to Joanne Hall (go get the instructions from the Glimakra USA web site), things should be straightened out when you step on the next pedal. But bungee cords will take care of that, anyway, they pull the shafts back up.

(Now I have a loom with horses, but somebody here has a loom with pulleys and/or rollers and no problems with 3/1 sheds so I hope yours will learn to behave! I happen to think that for four shafts counterbalance looms are greatly underrated.)

Have fun! Klara

sequel (not verified)

It looks like your ropes only go over the pulley.  Try going around the pulley one full wrap - you will see two ropes at the top but one at the bottom. You will need longer cords so the heddle eyes remain in line with the breast and warp beams.

When you treadle 1 shaft against 3 shafts you will get an unbalanced shed - weavable on some looms, less so on others.  The longer the heddles, the easier this seems to be, but loom geometry varies.

Textilis

 

Thank you all for your suggestions!

Dawn, that makes perfect sense about moving or removing lease sticks. I never changed it after tensioning the warp, which was pretty slippery, and one of my books suggested adding lots of sticks to help with this. That will be an easy fix to try.

Klara, I wondered about using elastic cord. Like you, I couldn't tell from my reading whether it would only be a cosmetic change, but it just might help if the harnesses are getting slightly snagged on each other, and if it fixes the irregular bits it would be great. I will make some "garters" for the loom directly. My heddle eyes were all even when I started out, but I have tinkered with the cord lengths some, so maybe I'll go back to zero and try these other suggestions first. 

Sequel, you are right about the cords only going over, rather than around both large and small pulleys, and that is a real difference between them and the roller types. The cords on the top pulleys are original to the loom, and are two passes of a hard string. I replaced the lower ones with textsolv, which is just thin enough to go through once, and certainly won't go twice. To try it, I would have to use finer cord of some kind. I also won't be able to anchor the cords at the top of the pulleys, as I think they do on rollers, since the pulleys are metal. Do you think it will help?

Also, when you say that longer heddles may help, do you mean longer heddle eyes, or longer heddles overall? (Maybe they go together.)

Thanks again for your advice!

 

Jennifer (Textilis)

 

Calico_Raven

this is my counter balance. they are finicky and i have to level it one in a while. had to reverse knots etc to get it to hang even. but it works great. don't be afraid to experiment.

 

sequel (not verified)

The length of the individual heddles, not the heddle eyes, determines the maximum shed.  The shed cannot be higher than the distance from one heddle bar to the heddle eye, or half the length of the heddle.  Of course the heddles cannot move any farther than the ropes that control them, so it's all relative.  Your loom probably has the right size heddles for it's height and distances involved.  If that gives you a shallow shed on balanced sheds, then your split shed will be smaller than that.  That's why we have those nice low profile shuttles! 

Textilis

Thank you to Red Raven Studios and Sequel for further posts. Red Raven it was nice to see someone with a loom as small as mine, and it looks as though you do beautiful things on it!

I removed the excess lease sticks and increased the distance from the remaining ones to the harnesses. That made my sheds bigger, but left the irregularity. I decided to start from scratch. I made myself some shaft holders (I had only been pinning the shafts in the past) and re-did all my tie-ups from lamms to shafts and from lamms to treadles. Then I made a set of elastics for the top shafts (see photo) and ALL BECAME BEAUTIFUL! I am just flying along now, with lovely sheds. I am thrilled. Thanks to all for your advice and encouragement. 

 

Dawn McCarthy

Congrats!  Looks great - enjoy weaving on it.

Dawn

 

ReedGuy

I also suspect the tipped up shafts were due to centring of the tie-on cord from the lam to the shafts. If not centered or if it can slip then the shafts will not balance. This balancing will also depend on how the heddles are threaded. If there are more to the left than the right, then the balance shifts right or left. Cords should be tied after the harnass height is adjusted so that the warp passes in the centre of the reed and then the warp is tied onto the cloth beam rod. Then you will see exactly how your tie-up is to be balanced with the cords. The treadles should be tied no higher from the floor than maybe an inch longer then the length of the heddle from eye to shaft bar (inside dimension). Years ago there were no such thing as bungees and things jury rigging a loom. A loom should work as designed or it's a failure that someone passed off to somene else.

Textilis

Reed guy, I'm sure that a lack of good centering was part of the problem, as I had initially beamed the warped for a different project, and ended up after re-threading with a group of unused yarns at one side. I did attempt to re-distribute my heddles to center the lamm cords, which pass through a hole in the center of the shaft length. The new threading also had significantly fewer heddles on the back two harnesses, compared with the front two, so there weren't many heddles over which to balance the tension back there. I will try my next warp without the elastics and see how it performs. I think I still need to play with treadle height for the sake of ergonomics, if not for anything else. I am still very new to this little old loom. Thanks for the advice. 

Submitted by Textilis on