I have just completed warping, sleying and tying onto the front apron rod a 10/2 cotton warp for an overshot project and cannot get everything back in balance.  I have tried 4 times starting with supporting the shafts in the shaft holders and then arranging the lamms so they are parallel to the floor.  Everything looks great, I remove the shaft holders and it all hangs crooked and I cannot get a clear shed on any treadle.  What am I doing wrong???  I have had this loom and my other Glimakra for 4 years and never had this much trouble.  

Thanks in advance for any ideas or suggestions.  I have Laila Lundell's book as well as both of Joanne Hall's books and am following their recommendations but nothing is working.   Clearly I have lost my brain.

Claudia, frustrated in Maryland

Comments

Claudia Segal (not verified)

I forgot the locking pins.  I have now put them in and will start over in the morning.  Is that the source of my woes?  I can't come up with anything else.  

Open to other suggestions.

Claudia

Joanne Hall

Hi Claudia,

Since you have been weaving on two countermarch looms for a long time, I am sure that it is just some little twist in a tie, or some tie got on the wrong side of something.  Perhaps it will jump out at you in the morning.  I will be teaching at the Woolery this week, but I am sure that you will get it figured out.

Joanne

Su Butler

HI Claudia...hope you got your problem solved, but in case you didn't.....perhaps your tie up is not balanced enough to keep the shafts and lamms in balance.  I sometimes have to tie up an extra two treadles to every other shaft to keep everything in balance.  Check your tie up and see if it is rather unbalanced.  Also, you said you made everything parallel to the floor...does this mean you are weaving on a Toika loom?  If a Glimakra, you may need to do the graduated tie up where you slowly lengthen each tie up cord as you move towards the front of the loom.

Claudia Segal (not verified)

Hi Su Am heading to the loom soon. It's a Glimakra Julia. Two questions; when you say to lengthen each tie up as I move closer to the front are You referringto the treadles? Second, is the idea to balance things starting from the top and move down? I am hoping the locking pins are my answer. I am seriously considering the pVavstuga treadle tie up system. Do you have any experience with that ? Claudia I didn't need to remove all the cords from the shafts to the lamms when I put on a new warp, did I ? I'm having trouble figuring out how to put a new warp on a countermarch loom and leave everything attached.

kerstinfroberg

I rarely do that, as I usually want a new tieup for every warp, but: if the new warp is narrow, you can just move the heddles from the middle out*, making a gap where you let the warp go through. If the warp is wider, just detach the lower shaft bar from the lamms. (Mark the cord, but don't use black or red, they tend to fade quicker than green...)

* of course that can be done by taking off all heddles instead, but I think that more work than I want to do. And... to ensure the heddles do not fall off the ends of the shaft bars, see the best trick ever on my website (thanks Barbro, I've been using your trick for over 25 years now!)

ReedGuy

If you tie a piece of cord with arrow pegs and button eye cord to the shaft bars so they don't slide off the ends. However to add or take off heddles you must remove this cord, which may seem like extra time. But it's not much time really. I only tie on to the top shaft bar with this cord.

In this image you can see the cords detached from the upper bars (at one end) and laid over the side. This draft went from 4 to 8 shafts so I have not attached the other 4 button eye cords to the back shafts. This particular draft is experimental to see how the yarn spreads with the epi I used. I discovered I need to double the # of blocks to get the width I want (20") for dish towels. So more heddles will be added on the ends of what is there. Two more blocks per end of the shafts to have a ballanced warp.

 

You don't have to remove the cords to put the warp on. Just the upper lamm cord to the centre of the lower shaft bars and the cords coming down from the jack cradle on the tower (the cords on the pullies) if your moving the shafts back by the warp beam to thread the heddles.I like going back there and I set my loom bench inside the loom and have a second function for the bench. ;D

Su Butler

Hey Claudia.....yes, when I say lenghthen each tie up I mean tie up cord....from the back where the cord is the shortest to the front where it is longest.  How much you have to lenghthen might be a matter of experimentation.  If you have WEAVERS issue 26, there is an article by MVDH about tying up a Glimakra, but I am uncertain how it relates to the Julia as I have never woven on that model.  Does the Julia have a back beam that is higher (from the floor) that the breast beam??

Balance - with locking pins in place your warp should run parallel to the floor from back beam to breast beam, going through the middle of each heddle.  If the back beam is higher than the breast beam, you warp will run at a slight angle, but there should be no dipping of the warp at any point.  Once the warp is in place (and you do not need to remove the cord from the shafts to the lamms, just split your warp and thread either from side to middle or middle to side), angle your upper lamms up just a tad and your lowers down just a tad and do your tie ups, starting at the back of the loom for each treadle.  After you remove the locking pins, check to see if the sheds are clean.  If they are, you don't really need to worry about the shafts or lamms being perfectly even, as long as they are not interfering with one another.  If the sheds are not clean, tie up a couple of extra treadles to help balance the whole thing.  I often find that tying up two extra treadles adds just enough weight to make everything work just great.    

I am not sure what you mean when you reference the Vavstuga system, but I have my CM loom set up so every hole in every treadle has one cord long enough to reach the upper lamms.  Each cord is tied to either an upper or lower lamm, and when tied to the upper it rides behind the lower lamm for the corresponding shaft.  There is a lot of Texsolv lying about over the lower lamms, but I have never had  a problem with it on my 16 shaft CM loom.  I anchor each cord to the lamm with an arrow pin.  Any treadles I am not using have the cords bundled and tied in a knot and thrown to the side of the treadles.  I have had this system in place for many years and it is very reliable and simple to use.  

As far as leaving everything attached when you warp up - as long as your locking pins are in place, this is fine.  It does make it a bit tricky to move heddles, but you can remedy that by putting a texsolve heddle on the end of each shaft, twisting it once or twice and slipping it over the lower shaft bar.  This will "pinch" the heddle bars together a bit and make the other heddles on the shafts a bit easier to move.  Once the warp is in place, if you want to use the same tie up, you can remove the locking pins and see if it balances.  It should.    Good luck Claudia - just remember it takes a bit of time to get used to a CM, but once you get it, it is like riding a bike - you never forget and it becomes quite easy.

Su :-)

Claudia Segal (not verified)

Thanks Su for taking time to write everything down for me.  I really needed the refresher and more that you provided.  If we had "like" buttons I would hit it at least a dozen times.

Once I put the locking pins in and removed the shaft holders, everything began to fall into place. LOL.  I needed to redo all the cords running from the lower and upper lamms to the treadles because some were in front of the lamms and some were behind.  There was no consistency on my part.  Now, all the cords run behind the lamms to get to the treadles.  It seems as though it doesn't really matter if they are in front or behind as long as it is consistent which mine were not.

I have now discovered a fairly serious threading error so I am going back and checking my threading from beginning to end.  Once I get that settled, I am off and running. 

THanks again to everyone for their suggestions and assistance.  I have bookmarked this thread for the future.

Claudia

Submitted by Anonymous (not verified) on