Hey I would like to know if anyone out there has restored a loom

What do you use to derust the Harness and Heddles?  

Do you use wood oil, wax or polish on the wooden parts of the loom

How hard is it to put back together if you take the loom apart

Any advise you can offer would be appreciated before I pull this loom apart that hasnt been used for nearly 30 years

 

Thanks for any help you can give

Comments

Joanne Hall

I would put a warp on it and weave a little to be sure that it is working, especially if it is not a brand name loom.  Then you will know if you want to keep the loom.

Joanne

mallasch

Hi Joanne...  its a 4 shaft Tekoteko Jack Loom - made in NZ.  It has a broken harness that needs soldering and the heddles are a bit rusty.  The warp and semi weave thats on it was put on 30 years ago and is rotten from the sun.  I would love to restore it as its actually a nice looking loom...  not super fancy but has that practical well used old look.  Im sure that there is someone out there that can advise me what to do.  I hope  or am I really wasting my time

 

Joanne Hall

I spent time on a number of old looms that really were not worth the time and effort I put into them.  Then there was a table loom that I acquired that I really should have discarded.  I did not realize just how many things needed to be fixed on that loom.  In all of these cases I spent more time fixing than I should have.  So, I suggest that you make the necessary repairs and then weave on it.  Not only do you need to decide if this loom actually works, is the loom you want, but also whether it is the type of loom you want.

Of course, the broken part needs to be fixed.  But I would not do any more than clean the loom before putting a new warp on it and trying it out.  Maybe it is a good loom.  After weaving on it,  decide if it suits you, then you can spend more time on making it look nice.

Whether you clean the reed is really dependent on how bad it is.  A new one is about $2.00 per inch, so you can use that to determine how much work you want to do on the reed.  You can clean the dents by moving your first warp threads up and down before you do the tie-up.  If a lot of rust comes off onto the thread, then it might need to be replaced.  Rust will pit the metal and even with cleaning it might not be a good reed.

Joanne

JoyP (not verified)

I just recently restored a Missouri Looms table loom and have just started on a Leclerc Fanny made in 1950. I have learned a great deal by reading posts on this site - just put "restore loom" in the search box and you will learn all kinds of useful information. Although the posts are not about your kind of loom, the information can assist in restoring any kind of loom. Although new to restoring looms, I have restored antique furniture for several decades and lessons learned in that have carried over to how I approach a loom. Yes, take tons of photographs of every aspect of the loom - they can be a lifesaver! Then, as you take it apart, label everything. I prefer to put things back exactly as they were (for example, the treadles placed back in the same order) so I number everything. You can find on this site how to test the existing finish to determine whether it is lacquer, varnish, etc, so the type of finish you use would vary depending on what is already there (unless you plan to remove all the existing finish). I used a Danish Oil finish on my table loom and on my spinning wheels (and lots of furniture in the past) and have always been very pleased with the results. It will not rub off on anything because it dries hard, and it is easily renewed with another coat to repair scuffs as time goes by. As noted in many other postings on this site, rusted reeds and heddles cannot be salvaged if the rust has gone deep enough to pit the metal. I use vinegar for a soak and then sand with a wire brush (in a drill or a Dremel), followed by 400 and 800 grit sandpaper to see if the items can be salvaged. Tedious work when it comes to the heddles especially, but sometimes it works! Good luck and have fun!

Edited with picures of my table loom, before and after

 

 

jennybellairs

I'm in the process of restoring a Weaver's Delight loom.  I started out by taking many photos from all angles, and lots of close-ups of joints.  If you take bolts out, bag and label them.  If you know the maker, you may be able to find specific information online. 

Jenny in Charlevoix the Beautiful

I'm blogging about mine at:

http://jennybellairs.blogspot.com

sandra.eberhar…

I can understand the attraction for restoring an old loom.  I got a barn frame loom that I have dated to the mid 1700's from a salvage dealer in Georgia.  It cost $100.  I spent a year and a half making treadles, headles, and new beams (the cloth and warp beams had been cut from tree trunks and were warped).  It started out as two harness loom with no metal parts.  In it's current configuration, it is an eight harness parallel countermarche.  It was made by a very good carpenter for someone about my size.  It treadles easily, has large sheds, is easy to warp, and I can work at it all day without strain or a sore back.  It is huge and massive.  When I read about people haveing trouble with their looms walking, i just laugh.  I think you can solve most problems with looms if you are willing to work with them; the most difficult problems that I have seen come from looms that are too shallow (space saving) or are too lightly built.

Sandra

mallasch

Well I pulled it all apart, cleaned heddles in vinegar and sanded and dried individually, sanded, scrubbed reed and oiled all wooden bits, resoldered the harness.  Looked online as to how to warp and loom using oldish wool as the rust kept reappearing on the reed overnight and started to weave.  WOW  I just loved it...  I made a table runner 54 inches long with various patterns used in the threading and in the treddling.  The harnesses are still a bit stiff and I crossed one thread over another between heddle and reed - which caused a fault throughout - but Im still happy with the end result.  thanks for the inspirational comments and advise.

Paula

 

Maurice

Tool collectors often use a very simple electrolic rust removal process. It removes all rust without removing any metal. The essentials are a box of washing soda, a container, a piece of stainless steel and a battery or battery charger. Here is a detailed link:

http://www.rickswoodshopcreations.com/Miscellaneous/Rust_Removal.htm

I have used the method for years, even on very large rusty pieces. Restored several reeds last year.

Maurice

Michael White

As was stated above good pictures are the key to getting everything back together. Rust, as Joann say, you will have to ask yourself "is it worth cleaning up the heddles and reed. If it is just a light rust it is doable. If the rust is heavy you run the risk of having pits which you will never be able to remove. 

steve104c (not verified)

I have found that when it comes to the heddles and the reed, rust is the victor and it is much easier to replace them with new ones. Texsol heddles are a very good replacement and a stainless reed will never rust. Just good advice from someone who has had to replace several rusty reeds and heddles on several refurbished looms.......Steve.

cindystrick

I am new to weaving and received a Medico 4 shaft table loom as a gift.  Some of the heddles are rusted but I do not know how to remove the shafts to clean them.

jander14indoor (not verified)

I had a LeClerc Medico for a while and wove my first projects on it.

Nice enough table top loom, I had the stand with treadles, but finally replaced it when I found more capable floor looms.

 

Now, the nice thing about LeClerc looms.  They make an effort to support event the older ones.  Check their website, they have a page dedicated to  old manuals.  http://www.leclerclooms.com/draw_inst/Draw_inst.htm

The Medico manual is there, doesn't entirely answer your qeustion though.  To remove the frames completely I had to dissassemble the castle.

I never had the top board, I just unscrewed the front board where the levers poke out.  BEFORE you do, take pictures, make drawings, make notes on how it goes back together and make sure you don't lose any small parts when you take the board off.  Its not hard to get back together, but you don't want to have to replace old parts.

 

Good luck,

Jeff Anderson

 

Submitted by mallasch on