Welcome to our Rigid Heddlers group second Weave-A-Long!

This WAL consists of 12 different 3S Twills woven on our Rigid Heddle looms set up with two heddles.

So grab your RH looms and two contrasting colors of yarn and lets have some fun.

The following draft has the warp one solid color and the weft a contrasting color.  Ten of the treadling sequences will be done with the weft a contrasting color.  The last two sequences will be done using one shuttle with the 'blue' weft color and a second shuttle with the 'yellow' warp color.  Of course, you are free to use whatever colors and yarn you want.

The first treadling sequence is actually a plain weave.  The second is a traditional 1/2 Twill and the third is a traditional 2/1 Twill.

For our Rigid Heddle looms the heddles are threaded as follows.  Heddle I is represented by the bottom holes and Heddle II is reprsented by the top holes.  Warp Thread 3 is threaded through the slots of both heddles.  Warp Thread 2 is threaded through the slot of Heddle I and a hole of Heddle II.  Warp Thread 1 is threaded through the hole of Heddle I and  a slot of Heddle II.

In a few days I will post more treadling sequences but please work at your own pace and feel free to ask lots of questions.

Now let the fun begin!!!!!!!!!!!!!!!

Susan

Comments

fiberphoenix (not verified)

Ooo - this looks like fun.  I think I'll have to try.

Thanks!

C

jordanj (not verified)

 Any recommendations for yarns to use with two 12 reeds? Would mercerized cotton be easier for a newbie than a wool yarn would be?

Looks like fun!

Jennifer

claudia (not verified)

Hi Jennifer,

Wool can be sticky, especially with 2 heddles and mercerized cotton slips and slides more easily.  I would suggest a 5/2 cotton since your sett with 2-12 heddles will be 16, not 24 since this is a twill, it's 150% not double.  The recommended sett for twill with 5/2 is 18-24 so it might be a bit loose.  The recommended sett for 3/2 is 12-15 so you are in between the two common sizes (for the US). 

Another choice is #3 crochet cotton which is readily available, not too costly and smooth. 

Keep us posted on which you choose.

Claudia

Alison (not verified)

 Hi Jennifer,

I used Zephyr on my hand painted scart (here) (2 12 dpi heddles on my Flip).  This is a plain weave, not a twill, so the danger would be that 24epi may not be dense enough.  That said, Jason's scarf (here), is a rosepath twill also at 24 epi (on the Baby Wolf).  I found the density perfect for that project.

As Claudia pointed out, the wool can be sticky, as can the Zephyr.  I had to be more careful on the Flip than on the Wolf.  If you really want to use wool, you could size it.  At the very least, spraying anti-static spray on it can help.

Alison

jordanj (not verified)

 Thanks for the suggestions. I think I will use 5/2 perle cotton as I have lots in the cupboard.

I have never done a WAL before. Since this is a sampler, would a 10" wide, 3 yds long warp be about right?

Jennifer

CraftinSusan

Jennifer,

I deliberately did not mention how long of a warp or how wide.  That is up to the weaver.   The question you need to ask yourself is what, if anything, did you want to do with the sampler.  If nothing, than you can make it as wide as you want and as long of a warp as you want.  Others like to cut up the sampler and attach the woven part to the paper draft or make mug rugs out of the samples.  If that is the way you want to go than you have to add extra warp for spacers. 

With a three yard warp and with 12 treadling sequences I estimate I can weave all twelve sequences each 6 inches long with maybe just a pick or two in between each sequence.  If I have any warp left I will pick my favorite pattern and weave a short dresser scarf.

Because this is a sampler I dove into my yarn stash and found a couple of skeins of "What Possessed Me To Buy This"  yarn.

Susan

kellytwo (not verified)

I'm going to make mine 6" wide and use a 3 yard long warp. Each sample will be 6" long so they're square. I like to keep my samplers intact so I can refer to them in the future. If there is some warp leftover, maybe I'll make some mug rugs from my favorite patterns.

Thank you for doing this Susan, I can't wait to get started.

Doreen

jordanj (not verified)

 Great idea on the 6" wide bit. And also for using the "what possessed me to buy this yarn". I have some 8/2 unmercerized cotton in colors that will never do for kitchen towels, so today I'm thinking I'll use that.

Now I have a question about heddle size:

I currently have one 10 dent and one 12 dent heddle and will purchase my 2nd heddle today. If I want to use my 8/2 wouldn't I use two 12 dent heddles for 24 epi? Claudia suggested a 5/2 for two 12's but that just seems too big to me. I have never done this before though, so maybe my math is just a bit wonky.... but there's probably a big piece of this puzzle that I'm missing!

 

CraftinSusan

If we were using a 4 shaft pattern of 1234 than, yes, two 12 dent heddles will be 24 EPI.  But we are using a 3 shaft pattern of 123 and with two12 dent heddles that will give us 18 EPI.

jordanj (not verified)

 Oh.... yes, that makes sense! And two 10 dent heddles with a 3 shaft pattern would be 15epi. Got it now!

Another question - can you tell I'm the newbie? :-)

Any special selvage treatments available on a RH for the twill threading? 

Jennifer

 

CraftinSusan

Generally with a sampler we don't worry about any special selvage treatments.  We can always wrap the weft thread around the edge warp thread as we weave.

If you are refering to a floating slevage, I am not sure about that.  The best we could do is to have an extra thread at each end that we could catch with the weft thread as we throw the shuttle.

Susan

sally t. (not verified)

I tried a floating selvedge on my last twill project.  If the end warps go through a slot in the front and a slot in the back, then when you weave you can always enter the shed by going over the first warp and leave the shed by going under the last warp. the weft will always alternate over/under at the selvedge.  that makes for a nice selvedge.  Does that make sense?

kellytwo (not verified)

The warp is on my loom and I'm ready to start first thing tomorrow morning.

Doreen

jordanj (not verified)

 I have my RH loom half way warped and am looking forward to starting weaving. I have never used two heddles before and am puzzled by the sequence in which the heddles will be moved in to make the different sheds for treadling.

Warp threads 1 and 2 are in holes, so to raise just these threads, one would just raise the appropriate heddle and leave the other down. But since warp thread 3 is in both slots, how is that raised? Do you use a pick up stick? 

 

CraftinSusan

There is a bit of a trick to using two or more heddles on a RH loom.  First, we bring the heddles forward so they are in front of the heddle block and the heddles just rest on the warp.

To get Shed 1 we push the heddles back against the heddle block and raise Heddle I.

To get Shed 2 we push both heddles back against the heddle block and raise Heddle II.

To get Shed 3 we push both heddles back against the heddle block and push both heddles down so Warp Thread #3 lifts up.

To get the different combinations of sheds we have to lift or push down the heddles.

For example, for Shed 1 & 3 we first push both heddles against the heddle block as well as pushing both heddles down to bring up Warp Thread #3.  Now we lift Heddle #1 to the same level as Warp Thread #3.

Can you work out the other sheds?

Yes, we can use a pick up stick to get Shed #3.  Push both heddles down to bring up Warp Thread #3 and insert a pick up stick behind the heddle block and under threads.  Now instead of pushing down both heddles we turn the pick up stick on its edge.  Others use a dowel rod and string heddles instead of a pick up stick.

Please experiment and see what works best for you and your loom to get the different sheds.  The 'right' way is the way it works best for you.

titadeb (not verified)

OK this looks totally fun.  I shall warp it this weekend, hopefully.  (pant, pant - trying to catch up!!!)

jordanj (not verified)

 Egads! I have not yet learned the lesson of not weaving after a day of work.

I finished warping and started a plain weave header and realized that the sett was way too wide and that I had done the threading all wrong! I had interpreted the diagram incorrectly. I thought that heddle two was slot, slot, hole - with the hole between the two slots empty. But now I'm looking at the diagram again and think it should be two threads in the same slot and then one thread in a hole. Is that right?  

CraftinSusan

Yes, that is correct.  Each heddle will have two threads in a slot and one in the hole.  For the wapring sequence of 123 there will be no skipped holes or slots.

claudia (not verified)

Good for you, you caught it early.  I had to rethread our first two heddle project 4 times and, even then, it was threaded wrong but it worked.  I'm looking forward to this WAL and getting the threading right this time.

I'll be joining y'all after MSWF which is this coming Saturday and Sunday.  We have 2 Meetups scheduled and Laverne is staying with us!!!  I am so excited, I'm like a little kid waking early every day to get things ready and clean the house and plan meals, etc.  Once we are past May 1 and 2, I'll get going and try to catch up.

If you know any weavers who live this way or who are going to Maryland Sheep and Wool, tell them about the Meetup. We'd love to have them join us.

Claudia

jordanj (not verified)

 Thanks for the encouragement Claudia! I have retreaded half the warp and will "sample" that tonight before I rethread the rest of the warp. I certainly hope I don't have to rethread 4 times! It's not like I can just add or subtract a heddle or two.

Lucky you for hosting Laverne! If I wasn't 2,000 miles away, I'd come to her class. Take lots of pictures and treat her well!

Jennifer

kellytwo (not verified)

My first two samples are done.  I really like sample #2, the 1/2 Twill.  I'm using two 8 dent heddles and 3/2 cotton thread. My warp is a natural color, and my weft is a variegated gold.  It was harder to beat the weft in sample 1 and make it look good, but sample 2 worked up very easy. Unfortunately when I was half done, I found a row with a mistake, but it was too late to fix it, and the reason I'm doing this WAL is to learn, so now I'm more careful.

Doreen

Momof4 (not verified)

I'll be following along and watching this WAL.  My second heddle hasn't come in yet.

claudia (not verified)

Hi Susan,

Just had a chance to read this through and want to make sure I understand.  You have posted three of the 12 different sequences or patterns, right?  I want to make sure I didn't miss something. 

I'll wind the warp tomorrow and get it on the loom and threaded.  The last time I used two heddles I wound the warp on a warping board and then threaded it through one heddle and beamed the warp on the back beam.  I then threaded from the back to the front.  Has anyone found an easier way to do this?  I suppose I could just treat it as if I were warping front to back and thread it correctly through both heddles and then beam the warp.  Direct warping was a disaster the first time I tried it so I am not doing that.

I'm open to suggestions, especially from those who have already started.

Thanks
Claudia

CraftinSusan

Claudia,

Yes, I have just posted three of the 12 different sequences so you haven't missed any.  LOL

I have direct warped like you did where I warped through the back heddle, beamed the warp and then threaded the front heddle.  I have also done indirect warping where I used lease sticks on my RH loom and threaded the heddles at the same time warping front to back.  I did not care for direct warping with multiple heddles so I used the indrect warping method for this WAL.  I do know that others have no problems with direct warping but I find it more confusing so indirect warping (front to back) is better for me.

Susan

jordanj (not verified)

 As I have had to rethread my warp several times now, i have had an opportunity to try out various ways of warping/threading. I have a Flip and I think the easiest for me is winding the warp on the warping board, thread heddle two while it is in the neutral slot (and I am sitting at the side), move Heddle to the rear position, then put heddle on in the neutral slot and thread it while sitting facing the loom. I got quite the rhythm in my head. Slot, Slot; Slot, Hole; Hole, Slot. :-)

I have finished the first two samples and agree with Kellytwo that the 2nd was "nicer" than the first.

Looking forward to working on #3 tomorrow.

Jennifer

CraftinSusan

Good evening, everyone!  How is everything going on the warping and the weaving?  Two people posted that the first pattern of plain weave was harder to beat in but the two twills were easy.  And they are right!  I wove all the samples in the book Weaving With Three Heddles by David McKinney.  The first part of the sampler was plain weave using one or two colors which I found hard to get the correct sett on and also hard to get a clear shed.  He then wrote that plain weave was harder to do on a Rigd Heddle loom set up with three heddles (and, as we are finding out, on a Rigid Heddle loom set up with two heddles).  He also wrote that twill was easy to do when compared to plain weave.  Something to think about when designing a project.

Now for the next two Twill drafts.  We are again using one color for the weft.

The first draft is a form of 1/2 Twill and the second is a form of 2/1 Twill.

Have fun with these and please post Work in Progress photos.  I can't wait to see everyone's work!

Susan

sally t. (not verified)

I have a question that is even confusing to ask.  So here goes.  I would usually raise heddle 1 for a shed. Or raise heddle 2.  Or lower heddles 1 and 2 (which would be my #3)  so on this last draft I think I need to be doing 1 and 3 at the same time.  Is that correct? Does that mean that I raise heddle 1 and lower heddle 2 to get that shed?  Hope this makes sense.  I have the book you used for inspiration, but he uses 3 heddles. I have a Schact Flip and 3 heddles seems impossible.  I can't  tell you how much I personally appreciate all the effort your posts must take.  I study them religiously.  I am somewhat of a closet weaver and they are so amazingly helpful.  Thanks Thanks Thanks! 

CraftinSusan

Wow, thank you for the compliment!

Now to answer your question when the shed calls for Shafts 1 & 3:

You are right that to get #3 we would lower both heddles to bring up Warp Thread 3 .  Then we push both heddles against the heddle block and raise Heddle I until Warp Thread 1 is the same level as Warp Thread 3.

Every loom is different as are the weavers.  It might be easier for you to push down Heddle II as you are raising up Heddle I.  Or is might work better to leave Heddle II in 'neutral' position and just lift Heddle I.  You will have to experiment to find out what gives you the better shed.

David McKinney in his book tells us how to get different sheds with the three heddles but I found that his method didn't always work for me and I just developed my own way for a couple of the sheds.

The only right way in this is the way that works to get the correct shed pattern and  a clear shed.

I have a 20 inch Schacht Flip as well as a Beka RL 32 inch loom on a stand.  I did the three heddle weaving on the Beka and the two heddle weaving on the Flip.  But if you look at the back of the Flip loom you will see another heddle slot.  So theoritically it is possible to use a third heddle on the Flip.  This is only my theory though as I have not played with it.  We only use the heddle slots when warping the loom.  The heddle(s) selection is done in front of the heddle block.

Susan

kellytwo (not verified)

On my Kromski 24" Harp, I am getting a good shed with using the two heddle blocks. But it's too much of a hassle to push them both down for shaft 3, so I'm using a pick up stick instead. I understand that it would work better by having both heddles in front of the first block, but I didn't like them hanging on the warp, so using a pick up stick for shaft 3 is working great. I haven't started the next sample yet, but I hope to have time to weave tomorrow. I'll post pictures when I'm done;

Doreen

CraftinSusan

A pick up stick works great!

I hope that others post with their tips.

Susan

mmorse (not verified)

Hello,

Thanks for the clear warping instructions (I love your hand-drawn pictures) and for the time you're taking to put this together. It's fun! I, too, have been puzzled by the 1-3 combination. My Kromski gives very good sheds for 1, 2, and 3 sitting in the blocks, rather than any of them hanging. (yes, pushing them both down is a bit of a pain, but there it is). From your description of how to get 1 and 3, I'm wondering whether 1 (the forward heddle) in neutral and 2 (the back) down would do it. I'll try when I get home from work this evening.

--mm

 

Tuesday morning: Yes, that works. 1 (front) in neutral and 2 (back) down gives the 1-3 combination, and 2 neutral, 1 down gives the 2-3 combination. Exciting to see weft floats change to warp floats.

amelia (not verified)

I am following along vicariously as my looms are busy with a variety of simple plain weave scarves at the moment.  I've woven a fair bit with 2 heddles on the Emilia, which has nice sheds; but as I get to the end of the warp, regardless of how many heddles I'm using, the shed shrinks, due to the shortness of the remaining warp. On the last one, I switched from boat to stick shuttles for a narrower profile of of the weft package passing through the warp. Your mention of David McKinney's methods reminded me ... next time, I will try his method of opening the shed and inserting a weaving sword (a fairly wide pick-up stick) and turn it on its side to make the shed generous enough for my boat shuttles to still pass comfortably through.

Thanks for that!

CraftinSusan

Thanks for posting your tips.

Susan

CraftinSusan

I haven't heard from anyone about the last two drafts.    Did anyone get a chance to weave them?

The following are the next three drafts for our Weave-A-Long.  We are still using a single color for the weft.

Have fun!

 

jordanj (not verified)

 I'm sorry, but I have had to drop out of this WAL. My choice of thread/sett was just not working. I was using 5/2 perle cotton with two 12 dent heddles and it was just too "sleezy". I think Claudia had predicted this! 

Since I have the warp on the loom, I didn't want to waste the thread and so I removed the heddles and recreated the cross and am now practicing my warp faced weaving techniques.

Thank you so much for organizing this WAL - all the work you have put into it is appreciated!  learned a lot and hopefully someone else will learn from my mistake!

Jennifer

mmorse (not verified)

Yes, I actually got them both to work. Pictures eventually. For what it's worth, I started with Dale Baby Ull, using 10-dent heddles. My warp and weft were too close in color, yellow and spring green, so I switched the weft to a charcoal sock yarn. Not nearly as pretty, but it's much easier to see what's going on.  I stopped the diamond twill after about 3 feet and rethreaded. For either, this yarn and dent combination produce a nice, fairly dense fabric.

I still have a lot to learn about e.p.i., draw-in, and the like. My sampler is about 3 inches wide, though I used about 50 ends, which would normally be somewhere approaching 5 inches. Would it be reasonable to guess about a third more ends to get the same width using this threading, given that you've got 3 ends for each pair of slots and holes?

--mlm

CraftinSusan

I am sorry that you had to drop out of the WAL.

I am also glad that you didn't have to totally frog the warp but are using it for something else.

Susan

kellytwo (not verified)

Hi Jennifer,  I'm surprised that your 5/2 perle cotton wasn't working with two 12 dent heddles. I just took a workshop with Jennifer Moore, and we used 5/2 perle cotton set at 16 epi, and it was perfect.  I think (and I may be wrong because this is new to me too) that using two 12 dent heddles and a twill pattern should be giving you 18 epi. That would be even a tighter weave than what we used in out workshop.

I'm using 3/2 cotton with two 8 dent heddles, which I was afraid would be too tight, but it's just fine.

I haven't been able to weave this week, but I'll get back to the WAL soon.

Doreen

CraftinSusan

The 150% on this warp pattern as compared to 100% throws a lot of us off.  When I first calculated the number of warp ends I would need I miscounted because I forgot about that.  I originally calculated 48 when I needed 72.

For me, I had warped 6 inches on the loom but I am getting 5 inches after weaving.  That is around 15% draw in when I expected 10% or less.  I used two 8 dent heddles because the WPI for this yarn was 21.  Divided by 2 gives me 10 so I normally would use a 10 dent heddle.  Because it is 150% I switched to two 8 dent heddles.  My woven fabric is great but I think that because the warp is so spread out I am getting more draw in than I expected.  It might be the yarn too.  Ahh, the mysteries of weaving!

You are right.  Twill produces a fairly dense fabric when compared to plain weave.   The fabric used for jeans is Twill.

Susan

mmorse (not verified)

Thanks for the explanation!

Just a quick note. I couldn't get the first two of the latest ones to work--bunched up threads on the front and long floats on the back--kind of interesting for a padded effect, but not what was supposed to happen, I think. The third one, though, worked. I'm out of warp, and I'll try again when I've put more on.

--mm

klhow74 (not verified)

Hi.  I am late joining in this WAL but better late than never right?  So just to make things quicker I warped only 5" wide and it's weaving up about 4" wide so I will have about 4x4 swatches of each fabric, which is fine by me.  The threading chart was very easy to follow.  So far I've only completed the first 3 drafts.  For the plain weave I decided to just put 3/4" of it between each draft and have one continuous sampler because I think my warp will only yield about 60 usable inches.  We'll see.  This is fun so far and not really hard.  It's funny because when I bought my loom (just 2 weeks ago) the lady at the store told me, "Now all you will be able to do is plain weave on this loom." 

Here is a picture of the progress not that it is much to see but I noticed no one has posted any progress pictures so I thought I could encourage people to do so by being the first.  I'm just using size 3 crochet thread because I have no intentions of this being anything other than a sampler.

CraftinSusan

"All you can do is plain weave" is a phrase that I have heard a lot.  I have also been told that Twill couldn't be done on a Rigid Heddle loom.  I hope that you will take your sampler back to the store and show that clerk!

You have only had your RH loom for two weeks and you are already using two heddles!  Fantastic!!!!!!!!!!!!!!!

#3 Crochet Cotton is great to use for a table runner or placemat.  A long time ago I used #10 Crochet Cotton on an 8S loom and wove a table runner.  Even after numerous washings and my husband, it still looks great.

I am glad that you posted progress pics and hope other join in. <hint, hint>

Susan

CraftinSusan

Is anyone ready for the next two drafts?  I have been playing with my new Inkle loom and haven't gotten back to the WAL.  My bad!  LOL

For those of you who are being 'good' here are the next two drafts.  After these there are just two more.

These are the last two drafts using one color for the weft. 

     

Have fun and keep posting updates!

Susan

kellytwo (not verified)

I'm back working on my sampler, and I agree with mmorse that sample # 6 and #7 aren't quite right.  In #6, thread 2 just floats along the back and never gets connected, and in #7, thread 1 floats the whole way. So after an inch of #6, I went on to sample 8 which is working okay. I hope to continue weaving more tomorrow.

Doreen

CraftinSusan

Hmm, I pulled the drafts from a book I have so I don't know what the weaver had in mind.  I am weaving the Twill samples too but I am not that far along.  I have gotten sidetracked.  I have been cleaning out my basement and weaving on my new wInkle loom.  Hopefully this weekend I can get caught up.

When I get a chance I will double check on those two drafts to see if I did it correctly.

Susan

claudia (not verified)

What's a winkle loom?  Got any pictures?

I am still threading, had a few other distractions this week.  More on that in the Weavolution News tomorrow.

Claudia

CraftinSusan

Sorry!  I meant to say Inkle loom.  I wish I could edit for spelling but it wouldn't let me.

mmorse (not verified)

Something that's true on my Kromski is that sometimes there are two sheds, an upper and a lower. Does the same thing happen on yours? Although I tried to be careful and consistent about using the wider one, it may be the wrong one. I need to get more scientific about figuring out which warps go with which heddle positions--I'm still using the "it's magic" approach and things often work out, but not with 6 and 7. More experimentation to come.

--mm

kellytwo (not verified)

On my Kromski, because I'm using the two heddle holders, I also have what appears to be 3 sheds because the holders are spread apart. If the heddles were held together like Susan suggested, I don't think you would have this problem, but I like to have my hands free, so I'm using the holders. If you're only raising one heddle you'll use the top shed because you've only raised one layer of warp, but if you raise, say shaft 1 and 2, then you would use the bottom shed because you've raised two layers of warp and you have to get under the two, and that leaves layer 3 unused on the bottom.  It's kind of hard to understand without being shown.  If you still don't understand, I can draw a diagram.  Let me know.

Doreen

Submitted by Anonymous (not verified) on