SundownAlpacas (not verified)

Sounds like you had alot of fun. The children will remember you, the person who spent time doing things with them. Great memories for all. I understand about the fidgeting. ;)

Katie Lacewell (not verified)

Okay, Joanne.  Will do.  It came with two treadles tied up for plain weave and when I checked that shed, it was awful.  So I locked the shafts and tied up the rest of the treadles (it's 8 harness, so 10 treadle) in a regular twill.  I'll see what I get this time!

Katie

Katie Lacewell (not verified)

Yes, I do have all 8 shafts threaded.  I monkeyed with it yesterday and today, and am learning the adjustments.  I have a decent shed - not perfect, but useable.

Katie Lacewell (not verified)

Okay, so I have this loom up and running.  I wove about a yard on it in plain weave, 19" wide in the reed.  Since I've never had a countermarche before, I'd appreciate comment on the following observations:

1.  The hanging beater is way cool.  I did not realize before that you coordinate your shuttle throw with the back motion of the beater, thereby creating a larger (since closer to the heddles) shed.  It lends itself to a lovely rocking motion for weaving, and the beater feels light as a feather, although I know (from two people required to lift it on) that's it's not.

2.  The draw in is pretty severe.  Granted I did not tie the end bouts of the warp out an angle, or put a first shot in and wrap it around the end of the apron tie sticks.  I'll try that next time.  However, the edge 1/4-1/2 inch of warp was compacted enough to cause the weft to not beat in sufficiently for a level shot.  I put a homemade temple on with a little extra weight, and it helped a lot.  Are temples for cloth weaving par for the course with this loom?

3.  My shed is good as far as level top and bottom.  However, it is still not what I would call a great shed.  It's okay for my boat shuttles but I'm thinking rag shuttles for rugs are going to be a headache.  I have adjusted and adjusted, following your book, Joanne. Threads are through the middle of the heddles, and through the middle of the reed.  If I shorten the short treadle ties any further, the treadles run into the lamms.  Any hints on what else I could do?  FYI, no lamms are weighted.

Thanks for your help, guys.


Katie

Katie Lacewell (not verified)

Okay.  Thanks, Joanne.  I'll check on threads when the shafts are in use and also on straight back to front, although I'm pretty sure that one is okay.  I'm used to weaving rugs on a counterbalance, and it had a 5 inch reed, so it had the capacity for wider sheds.  I hope to not be weaving a LOT of rugs with this loom, since I'm moving out of production weaving and into personal weaving, but I do have a couple custom  orders here and there.

 

Thanks again for your help.

Katie

Katie Lacewell (not verified)

Hi Kerstin

I never know if what I do is common or not, since I live in the middle of the boonies.  I do have a weaving guild that meets once a month.  It's 2 hours away by car and well worth the travel.  I read books, the internet, and trial and error - not sure where I got the "loop the first shot around the ends of the apron tie stick."

The draw-in problem is resolved pretty well with the homemade temple.  I'm ordering a "real" one for these smaller width pieces.  I have a wider one already.

Joanne, I did check the heddles when the shed is open and  they are against the oppositely raised (or lowered) shaft bars.  So, no wiggle room there.  Also the warp is straight front to back, and if I tie up any tighter, I'm striking the lamms when treadling.  I don't see any place to change anything.  I'll probably just get used to this shed width.  If I ever have the luck of meeting up with a Cranbrook owner, I'll drag them to my house for an inspection.  I really do appreciate your help, though.

Katie

Katie Lacewell (not verified)

Well, that's about what mine is, so guess I'm good to go.  Thanks, Sara, for putting a tape to your loom shed.  Now I'll just go on about the business of falling completely in love with this loom.


Katie

mhoffhe (not verified)

Karren, My Grandson is currently in Ghana for a month working on a Project called "Pure Home Water", to bring safe drinking water to the village.  I sent some money with him and asked him to see if he could purchase some Kente cloth for me while he is there.  I'm hopeful.. and anxious to see what he may find.  Middy

kbird (not verified)

I get it... a distraction by knitting... *grin*

Syne Mitchell (not verified)

We've got two great interviews for you this episode: Jacey Boggs, the leader of the new art-yarn movement talks about creating wild and yet structurally sound yarns, and then John Acord of Flatwater Electronics describes his new hardware interface that  breathes new life into electronically obsolete computer dobby looms. Listen to the show >>