Mike (not verified)

The first picture is taken looking down onto the back of the loom.  The circular silver bar is the Warp Beam.  Attached to it by Texsolv cord is the back Apron Bar, which is draped over the Back Beam.  Then alongside the Texsolv cords are the "Loops" to which I am meant to connect the Back Stick, which passes through the warp.  It's the use of these "loops" that I find difficult.

 

  The second picture is the "Ashford" plastic connector.

Hope all this makes sense.  Thanks again. Mike

Mike (not verified)

I solved the problem by doing without the second stick, removing the Apron Stick and then sliding it through the loops on the raddle and the loops on the Back Beam in turn.

Caroline (not verified)

hi Jerri, Any twist in the yarn will come back once its wet, so you may be pleasantly surprised and find you have the effect you were after.

I also leave my yarns as singles, often because I'm not sure with what I want to ply them, or how I want to ply them - it leaves my options open. And I have also  re-spun or un-spun them if necessary. One thing I do though is wash them. I do not weight the skeins as they are drying, so I can see what it is I have, and to even out the twist. I only leave yarn in a ball if I am about to ply it within a few days.

lkautio (not verified)

If I were able to spin such a beautiful warp (I'm not a spinner or color expert), my impulse would be to sett it warp faced and weave it with sewing thread or 60/2 silk so all that beauty would shine through.  I'd use a smooth rather than fuzzy weft (again to avoid obscuring the warp) and experiment with whether I liked plain weave or the rosepath better.

good luck!

Laurie Autio

jeannine (not verified)

I think he is quite an artist . All the ways to eliminate trash are good and the result is special. 

Aunt Janet (not verified)

I love his work!  I love that he works in several techniques, and his media is limited only to what he can find.  I really love his looms!  Very inspiring work!  Makes me want to go pick up trash.  Unfortunately the skies have opened up in a big way in Humboldt Co, California.  Our first big storm of the season is a serious one. Not good trash picking up weather.

 

lkautio (not verified)

Sounds like you had all sorts of fun! Hope the rest of the workshop went better.  I know you won't ever need this <g> but there are some on the hoof solutions.  If you have a knife you can run a slit up the side of the straw and make that bad boy fit any winder.  Or use a paper pirn instead (cut an oval of paper and wrap it tightly onto the spindle).  

cheers,

Laurie Autio

dteaj (not verified)

Paper can also be turned into a quill. Cut or tear to  the right length and tape down with scotch tape.

I use rubber bands to shim a bobbin, quill or spool which is too large for the winder.

I use these things at home, since I wind off a great wheel. I haven't thought to bring them to a workshop, but I will from now on. That is the joy of weave-fail!

Debbie

Claudia Segal (not verified)

I found some very old comments here about winding bobbins.  

Not sure if that's what you're looking for.  There are tons of comments on winding bobbins, pirns and quills.  We do have an advanced search if you want to dig deeper for the comments.  So many search word possibilities.  I tried because I remember the discussion.  It was about a year ago.

Claudia

Claudia Segal (not verified)

Hi Peg,

When I had this problem, Joanne Hall said to start at the top and work my way down.  Support the shafts and check all the cords including the ones to the lamms.  She also sent me a page, as did Marie, about how to handle a narrow warp which can influence the balance of the shafts.  There is a page in the Laila Lundell Big Book of Weaving and she talks about running a doubled length of "fishyarn" or cotton rug warp from the front to the back beam and through the shafts to to help this problem.  

Claudia

I wrote about the same issue, different loom, here.