sandeleh (not verified)

I only check over here a couple of times a week - the forums are tricky to get around in, and if you happen to reply to an individual msg instead of at the end, the notification email you get will not send you to the new reply.  As far as I know, that notification email doesnt work well for anything on the 2nd or later pages of the forum anyway.   It does take some getting used to.

All of my yahoo email downloads into Outlook and gets filtered into separate folders, just waiting for me to read by group.  It is easier as far as the reading of msgs goes.

Sande in Fresno, CA, USA

 

Bonnie Datta (not verified)

Here's what's on mine...

This is a weft-face weave woven on a rosepath threading (12341432).  I'm still using up a spool of the fine cotton yarn, and for this it is used double and sleyed at 5 epi.  The weave is mushy but the pattern is showing up.  This could be a mug-rug, small hanging, hot pad, pot holder -- I plan to felt it a bit to firm it up.  I have a day or two more to do and I'll post the finished piece in projects.

crosstownshuttler (not verified)

Hi Bonnie,

I love your sheep! They almost look like they are dancing on the fence.

It's hard to see because it is also gray, but that looks like a piece of plastic pipe over the front beam. What a great idea for eliminating that sharp edge. Do you think it would round it enough to use a paper warp about the size of 5/2 cotton?

Carie

Bonnie Datta (not verified)

Hi Carie.  Yes, that is a 1" piece of PVC pipe, slit along one side and slipped over the metal front beam.  It totally eliminates that nasty problem of the front beam moving your weft picks around.  I had one on the back too, but it got lost.  It's only purpose was to raise the back beam so the warp ran perfectly level to the front beam.  Anyway, everything works fine without it.  With that pipe on the front beam I can weave very delicate, slippery yarns and very open structures and get no distortion.  Don't know about paper warp though.

crosstownshuttler (not verified)

Thanks Bonnie,

I think I'll try it for our guild's upcoming yarn tasting. Handwoven had waffle weave paper mats that looked fun. One inch pipe is now on the Home Depot shopping list :)

Carie 

maurerwerks (not verified)

Hi - I'm a newbie Structoer.  A friend came to work and dumped a poor, sad, table loom on my desk a few months back and said he found it in the dump and thought of me.  Hmmmm.  Anyways, it had no label on it anywhere that I found on a cursory inspection.  Rusted reed and heddles and the "jack" mechanism needed help.  I didn't know what it was until I went to a guild meeting and one of the looms that was being demoed on was a Structo and twin to mine.  I was so happy to find out what it was.  And I was so happy to find this group!   I still have to get around to fixing it up.  I normally weave on an 8-shaft floor loom, but I can think of plenty of things that would be much easier on this little guy.  Any advice for me in the arena of fixing it up?

Sue

weaversouth (not verified)

join us over on the Yahoo group..all_things_structo

I tried to migrate it over here, but we have so many archives and files it proved a bit frustrating.

Nancy C (listmom)

Pam Howard (not verified)

Hello there

I was looking through some forums tonight and found this one.  I got tickled because in the description of the group it talked about the little structos and a warp weighted loom.   Well I am sitting in my studio an owner of three tiny structos a warp weighted loom by my side.  I had just had my dear friend for Shetland to help me warp it up this past week.

I don't weave much on my little structos, but I do think they have their place in the weaving world.

Pam Howard

Resident Weaver - John C. Campbell Folk School

Brasstown, NC

kellytwo (not verified)

I just bought an 8" Structo loom yesterday from a friend. I never saw one before, so I'm really happy to see a group for it. I'll join the yahoo group too.( It' so cute, I just love it.)

Doreen