pamengberg (not verified)

Hi, everyone - some comments about the cactusflower looms:

My weaving group (Brimfield, MA) here has all 3 sizes - the tiny mini, the maxi, and the table loom. I am using the table loom, and I like it a lot. However, we also are having issues with the metal combs - they don't seem to be "finished" enough so the warp sometimes gets cut, even when you are very careful. So - I have a friend who is going to take me to meet his machinist buddy, and we are going to look at two options: (1) See if he can polish the combs to smooth them off; and.or (2) see of he can make combs of his own design that we can use to replace the existing ones. Ideally I'd like to be able to change the sett. My students like to use Burnham's #2 size Navajo yarn (the thicker size) and 9 epi is too close for that so they struggle with the Maxis' sett. The table loom comes with an 8 epi comb, which allows you to use either the Burnham's #2 size or the #1 finer size, or two fine strands together to blend colors. (You can get to Burnham's via Mary Walker's site or directly at http://rbburnhamtrading.com. ) I will let you know the outcome.

However - I know Jennie Slick uses one a lot, so maybe she or Mary has some suggestions about how to cope with the sharp edges? It doesn't seem to be a problem for Jennie!!

About the side cords: Below are photos of the attachment to the cactus flower, bottom and top - I put the cord in the slots adjacent to the edge warp, because I like to use the method where you weave it with the edge warp (it's easier for me to remember). So, at the bottom, it actually goes with one cord in the adjacent slot, one in the next slot, and the knot keeps it in place; then at the top I bring them again, in front, one through the slot adjacent to the edge warp, one in the slot next to it; then over the top of the top beam, down around it, and tie them in a bow around themselves. Hard to explain in words, but maybe the photos will clarify? If not, let me know; I'll get my husband to wield the camera - he's much better.

Marsha A. Knox (not verified)

I built my loom from the hardware store.  It is based on Navajo and the Mirrix loom.  Very economical and after years of trial and error I have finally perfected it to what I need and want in my loom.

Melinda CK (not verified)

I am hoping you meant 50" long....

Do you have a loom yet?  I have used Navajo waeaving techniques on a treadle floor loom, 2 harness.  The one I used has a 45 inch reed and continuous warp. 

 

Melinda CK (not verified)

here is some more - shuttles are nice but not required, bobbins are nice but you can live without them! Organize your yarn in 'butterflies"  (figure 8's around your thumb and index finger) and you will be fine until you have a better idea of what you want to do. Shuttles are helpful if you are weaving across a broad (wide) area and you really can't use them on a vertical loom very well unless you have a pretty deep shed (like 3 inches) which you probably don't have.

 

there is another book by Rachel Brown. She is the founder of Weaving Southwest in Taos - can't remember the name of it but you can get it on Amazon.  It is a comprehensive guide to differnt kinds of weaving. Very helpful and not as arrogant as some of the other literature tends to be.

eggplantlady (not verified)

Forgive the newbie question, but is the purpose of chaining for storage?  The only time I have used a warping board I went straight from the board to warping the loom.

Kurt Pippin (not verified)

I've started to chain every warp in sections, every time I stop, even if it's just an inch or two of ends. When I'm ready to beam the warp, I then divide the sections more evenly and chain them again. The weight is very helpful if you don't have a companion to hold tension while you wind on.

And I rarely use a warping board, but I also rarely use yarn as it comes off the skein for a warp. I'm either mixing yarns or randomly choosing colour or arranging and rearranging colours, so I just thread and tie onto the back apron rod 2 by 2. That's probably painfully slow for most weavers, but I consider the warp as half of the weaving, and the most important half. It's fairly easy to unweave a weft that seems to be rank, but doing a warp over is major.

Pippin

knitsalot (not verified)

I think that is the warping peg that you use to direct warp.  a rod from one of the clamps goes in the hole to clamp it to the table.

 

But I havent used it yet, so I ask someone else to verify.....

Manicgirl (not verified)

Yes, that would make sense! I've only warped on the loom itself, never tried direct warping.

Thanks! Until someone else says it something different, I'll go with that! :)

claudia (not verified)

I am here to verify, it is a warping peg.  You use one of the clamps that came with the loom to clamp it to a table to wind direct warps.  It's very handy and a quick easy way to put on a short warp.

Claudia, Kromski owner and lover for 2 years

knitsalot (not verified)

 thanks Claudia!